|
|
|
UEI Nevo Remote Controls Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
Nevo Q50 new units cannot upgrade...
| |
|
Topic: | Nevo Q50 new units cannot upgrade firmware???? This thread has 1 response. Displaying all posts. |
|
Post 1 made on Monday January 6, 2020 at 19:47 |
RemoteQuest Long Time Member |
Joined: Posts: | October 2008 245 |
|
|
Hi Folks,
Anyone have any advice on this? I have several new-in-box Q50's which I hoped would get me through several years. Decided to put a new one in play today and it will not update to the new firmware. I tried it on my Win 10 box which is working well for updating and saving to the remote. Also tried on two other Win 7 boxes and it just seems to fail to go to the newer firmware and then appears to brick the unit. Tried two new units today, same outcome.
There are times before the attempt at the firmware update that NSP sees the unit Mac address in NSP but once I attempt the firmware update it never finishes and sort-of bricks the unit.
I read somewhere that maybe the MS Mobile Device Center is the problem? Possibly it needs updates after Windows updates kills it? Is it simply that the firmware update cannot work any longer due to closed software and servers from UEI or is the firmware update built into NSP and resides on my local system? There is only one old firmware update which is needed.
Older units I have with the newer firmware can be updated and saved and work fine, even on my Win 10 box.
Are there newer version(s) of Windows Mobile Device Center which need to be installed to make this work?
I'm rather unhappy with all of this new-in-box Q50 inventory which I cannot update the firmware and will therefore no longer work.
Looking for any help you all might offer.
Thx Dave
|
|
OP | Post 2 made on Thursday January 9, 2020 at 15:32 |
RemoteQuest Long Time Member |
Joined: Posts: | October 2008 245 |
|
|
Worked on it for a few days and got lucky and finally figured it out!!!
I should have looked at the system info in the Q50 before I got started. They were basically functional with the stock config in them. It may have saved me all of this experimentation.
Especially since when you connect the Q50 to the PC, it tells you it needs to update the software on the remote and tells you to put it in USB download mode. That turned out to not be entirely accurate.
It needed to update the "Nevo Q50 version" in the remote, not the firmware. All of the remotes I had were setup for the earlier version of NSP. The firmware was already at the latest version (4.0.5.0) and I guess by trying to update it, was what bricked the units. And to update the firmware you have to put the unit into USB Download mode. Once bricked by the firmware update not finishing, in USB download mode, WMDC nor the PC would see the unit.
I was just experimenting and noticed if I didn't put the bricked unit into USB Download, WMDC would see the unit and so would NSP. So, I went to firmware download again, where there are 5-6 items that can be checked or unchecked. I unchecked everything except to update the NSP version. The old NSP version in these units was ver 1.1.0.249.
Immediately, it started to download whatever was needed so the unit could communicate with the latest version of NSP and set it up for NSP ver 3.0.0.562, which is the version of NSP which was installed on my pc that I was using.
The units were then un-bricked and came up to the normal calendar/time setup screen. Then I download my current config and all was good!!! Sort of stumbled upon it doing some experimentation. So, I have a nice brand new unit in my living room now and have a few more in boxes.
I have a 3rd brand new unit updated but the damn roller button is broken. That was certainly the bane of that model. That weak, add-on piece they put onto the roller, on the right-side of the remote. I have learned that if done carefully, I can super glue the add-on piece to the roller and if aligned well, it seems to hold up long-term. Of course you have to open up the remote to get to the roller and the roller add-on part.
Anyway, thought I would put this on RC in case it might help others. If you need more info or have questions, drop me an email. I don't get on RC very often, to see any PM's. Send an email to dd at eaglepoint2 dot com.
Regards...Dave D
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|