|
 |
|
The following page was printed from RemoteCentral.com:
Topic: | Xbox 360 Codes For T2-C This thread has 17 replies. Displaying posts 1 through 15. |
|
Post 1 made on Friday May 18, 2007 at 21:13 |
lites4u Active Member |
Joined: Posts: | August 2006 745 |
|
|
I tryed the xbox 360 codes from the master library on my T2-C and they don't work correctly. In order to get a discrete power on command I had to create a macro that takes the following commands A,X,Y,B,Start. Then it goes to the Media center page on the 360 but at least turns it on.
Does anyone have any discrete power on and power off commands for the 360 that work. Even the power toggle i n the library doesn't work all the time.
thanks
|
|
Post 2 made on Monday May 21, 2007 at 10:26 |
JoeyCes One In A Million |
Joined: Posts: | May 2004 1,329 |
|
|
|
Post 3 made on Thursday May 24, 2007 at 03:30 |
BigZAJ Long Time Member |
Joined: Posts: | April 2007 87 |
|
|
would you mind posting your flag setup for the power? I have found that usually the code for XBOX360 turns my xbox on and the code from the XBOX 360 (note the space) turns mine off. Although sometimes the toggle gets flipped for no reason and they switch (of course using the power switch does it too). So i'd like to know how to use flags to fix that little annoyance.
|
|
Post 4 made on Thursday May 24, 2007 at 08:50 |
estech Active Member |
Joined: Posts: | August 2002 584 |
|
|
On May 24, 2007 at 03:30, BigZAJ said...
Although sometimes the toggle gets flipped for no reason and they switch (of course using the power switch does it too). Flags are of no use if the power switch gets used. They will be most effective if the RTI control is the only way Power is switched. An example Power On Macro using a standard toggle Power command: If flag PowerStatus is set then --Else----- PowerOn-Off Set Flag: PowerStatus The Power Off Macro is just the opposite: If flag PowerStatus is set then PowerOn-Off Clear Flag: PowerStatus --Else-----
|
Pay no attention to that man behind the curtain. |
|
Post 5 made on Thursday November 15, 2007 at 20:54 |
vitoasaro Lurking Member |
Joined: Posts: | November 2007 5 |
|
|
On May 24, 2007 at 08:50, estech said...
Flags are of no use if the power switch gets used. They will be most effective if the RTI control is the only way Power is switched. Forgive my candor, estech, but your reply doesn't address or answer the problem by lites4u. The significance of discrete power-on/off codes is relevant if the Xbox-360 does not acknowledge/receive the command from the remote. In this case, even if you do use flags, then the flag status on the remote is invalid, and simply sending a power-toggle command to the Xbox-360 (and other components) might produce the opposite of the desired effect (everything off except for the Xbox-360, or everything else on instead..., etc). How can something like the AVF-300 have the discrete on/off codes for the Xbox-360, but the RTI T2-C not?
|
-V
|
|
Post 6 made on Thursday November 15, 2007 at 21:14 |
Glackowitz RC Moderator |
Joined: Posts: | May 2002 3,786 |
|
|
Whats an AVF-300 remote?? If it spits out IR the RTI line can learn it The RTI can learn IR freq's from 15 to 460mhz...most all other remotes will only learn in the 30-40mhz range In the RTI software there are 7 ir files for the Xbox...none have discrete power If you have the codes, could you post them In a pronto Hex format for us? ****Edit********* Ok Found some if anyone can test them for me I will add them to the Mega List Power off 0000 0073 0000 001F 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0031 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0020 0020 0020 0010 0010 0010 0010 0010 0010 0020 0020 0020 0020 0010 0010 0020 09D1 Power On 0000 0073 0000 0020 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0031 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0020 0020 0010 0010 0010 0010 0010 0010 0020 0020 0020 0020 0020 0020 0010 09C1
Last edited by Glackowitz
on November 15, 2007 21:40.
|
There's no worse feeling than that millisecond you're sure you are going to die after leaning your chair back a little too far. |
|
Post 7 made on Thursday November 15, 2007 at 22:15 |
brandenpro Select Member |
Joined: Posts: | May 2005 1,651 |
|
|
Power ON: 0000 0067 0000 0020 0069 0023 0011 0011 0011 0011 0011 0023 0011 0023 0036 0023 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0023 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0023 0023 0023 0011 0011 0011 0011 0011 0011 0023 0023 0023 0023 0023 0023 0011 0AA3
Power OFF: 0000 0067 0000 001F 0069 0023 0011 0011 0011 0011 0011 0023 0011 0023 0036 0023 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0023 0011 0011 0011 0011 0011 0011 0023 0023 0011 0011 0011 0011 0023 0023 0023 0011 0011 0011 0011 0011 0011 0023 0023 0023 0023 0011 0011 0023 0AB9
I have these working on my Xbox 360. There is another set floating around that flip from ON to OFF if you use the front panel to turn the Xbox ON or OFF. The codes above are working on multiple installations.
Glack those codes are in the Library I sent you last week.
|
|
Post 8 made on Thursday November 15, 2007 at 22:23 |
Glackowitz RC Moderator |
Joined: Posts: | May 2002 3,786 |
|
|
Im on my home computer and its not up to date with the mega list I guess they are already in the mega list then Thanks for the reminder...LOL On November 15, 2007 at 22:15, brandenpro said...
Power ON:
0000 0067 0000 0020 0069 0023 0011 0011 0011 0011 0011 0023 0011 0023 0036 0023 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0023 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0023 0023 0023 0011 0011 0011 0011 0011 0011 0023 0023 0023 0023 0023 0023 0011 0AA3
Power OFF: 0000 0067 0000 001F 0069 0023 0011 0011 0011 0011 0011 0023 0011 0023 0036 0023 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0011 0023 0011 0011 0011 0011 0011 0011 0023 0023 0011 0011 0011 0011 0023 0023 0023 0011 0011 0011 0011 0011 0011 0023 0023 0023 0023 0011 0011 0023 0AB9
I have these working on my Xbox 360. There is another set floating around that flip from ON to OFF if you use the front panel to turn the Xbox ON or OFF. The codes above are working on multiple installations.
Glack those codes are in the Library I sent you last week.
|
There's no worse feeling than that millisecond you're sure you are going to die after leaning your chair back a little too far. |
|
Post 9 made on Friday November 16, 2007 at 01:09 |
estech Active Member |
Joined: Posts: | August 2002 584 |
|
|
On November 15, 2007 at 20:54, vitoasaro said...
Forgive my candor, estech, but your reply doesn't address or answer the problem by lites4u. That's probably why I quoted the post I was responding to. The significance of discrete power-on/off codes is relevant if the Xbox-360 does not acknowledge/receive the command from the remote. In this case, even if you do use flags, then the flag status on the remote is invalid, and simply sending a power-toggle command to the Xbox-360 (and other components) might produce the opposite of the desired effect (everything off except for the Xbox-360, or everything else on instead..., etc). That's probably why I specified using the original toggle power command with flags. How can something like the AVF-300 have the discrete on/off codes for the Xbox-360, but the RTI T2-C not? I'm guessing that's a predecessor to the Monster AVL300, similar to the Harmony in that you log into Monster's site to program your devices. Based on so many posts about the XBox power commands flip-flopping, they are probably toggle-bit commands, and Monster has accounted for this in their remote's design. The RTI programming can also handle this. I just haven't seen the two sets of commands needed.
|
Pay no attention to that man behind the curtain. |
|
Post 10 made on Friday November 16, 2007 at 03:03 |
estech Active Member |
Joined: Posts: | August 2002 584 |
|
|
Glackowitz / brandenpro, I tested both set of codes above and here's my results: They both are discrete sets, however, if the power button on the Xbox is pressed between these commands, without anything else being pressed, the Xbox will ignore the next issue of the same command.
For example: If the xbox was turned off with the PowerOff command, then turned on with the PowerOn command, then manually turned off at the front panel, the xbox will ignore the PowerOn command, until another command is sent. Even though it is off at this point, another command flips a toggle and allows the PowerOn command to get through. The same is true in reverse with PowerOff command and a manual turn on. This happened with both sets of codes above.
Now this got me thinking, so I grabbed the Xbox remote (Joytech) that I think came with a cable I bought (I don't have the HD-DVD add-on), and learned a few commands twice through the IR-PRO, and sure enough, each one had two different hex codes from successive learns.
So this remote has a "#" button, which I have no idea whether it does anything to the normal xbox operation, but I used it's code set in different combinations with the discrete power commands, and was able to form two macros that performed without fail as discrete power commands. I tried repeated tests of manual power presses and different commands, and couldn't trip them up.
I know it's not the perfect single discrete command, but here it is:
Power On Macro (#a) 0000 0072 0000 0021 0062 0020 000F 000F 000F 000F 000F 0020 000F 0020 002F 0020 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0020 000F 000F 000F 000F 000F 000F 0020 0020 000F 000F 000F 000F 0020 0020 0020 000F 000F 000F 000F 000F 000F 000F 000F 0020 000F 000F 000F 000F 0020 000F 000F 000F 0981 (Power On) 0000 0073 0000 0020 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0031 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0020 0020 0010 0010 0010 0010 0010 0010 0020 0020 0020 0020 0020 0020 0010 09C1
Power Off Macro (#b) 0000 0072 0022 0022 0062 0020 000F 000F 000F 000F 000F 0020 000F 0020 002F 0020 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0020 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0020 0020 0020 000F 000F 000F 000F 000F 000F 000F 000F 0020 000F 000F 000F 000F 0020 000F 000F 000F 0981 0062 0020 000F 000F 000F 000F 000F 0020 000F 0020 002F 0020 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0020 000F 000F 000F 000F 000F 000F 0012 000F 000F 000F 000F 000F 000F 000F 0020 0020 0020 000F 000F 000F 000F 000F 000F 000F 000F 0020 000F 000F 000F 000F 0020 000F 000F 000F 0981 (Power Off) 0000 0073 0000 001F 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0031 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0020 0020 0020 0010 0010 0010 0010 0010 0010 0020 0020 0020 0020 0010 0010 0020 09D1
|
Pay no attention to that man behind the curtain. |
|
Post 11 made on Friday November 16, 2007 at 19:32 |
brandenpro Select Member |
Joined: Posts: | May 2005 1,651 |
|
|
I just tried it and you are correct.
|
|
Post 12 made on Monday December 3, 2007 at 04:05 |
gumppy Lurking Member |
Joined: Posts: | November 2007 3 |
|
|
Has anyone had any problems with the navkeys just not working. I have tried learning them,using the library and praying any one got a set by any chance. I need UP, DOWN ,LEFT ,RIGHT and OK please.
|
|
Post 13 made on Thursday November 19, 2009 at 15:26 |
joshmwilliams Lurking Member |
Joined: Posts: | November 2009 7 |
|
|
I have been searching for a solution to the mysterious "flipping" of the on/off power codes for ages.. This did the trick! Thanks a million.
|
|
Post 14 made on Thursday November 19, 2009 at 16:20 |
cdouglass Long Time Member |
Joined: Posts: | February 2008 166 |
|
|
Man this thread was from 2 years ago, I read all the way through before realizing it. Curb your enthusiasm.
|
|
Post 15 made on Friday November 20, 2009 at 18:28 |
pesci Senior Member |
Joined: Posts: | August 2006 1,194 |
|
|
hahahah me too!!!!!! whoa! i wonder if the above works?
|
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|