 |
 |
|
|
RS-232 & IP Control Forum - View Post
|
|
 |
|
10/10/25 - It’s been so long since we’ve last seen you!
10/24/22 - In searching for the perfect day, Timmy discovers something unexpected!
9/04/22 - That childhood favorite is back in a new Timmy video.
7/31/22 - It’s time for my second new Just Like Timmy video!
7/12/22 - Why not check out my new YouTube animation channel, Just Like Timmy!
|
|
 |
|
|
The following page was printed from RemoteCentral.com:
|
Pioneer Elite SC-55 Power On
| |
|
| Topic: | Pioneer Elite SC-55 Power On This thread has 11 replies. Displaying all posts. |
|
| Post 1 made on February 18, 2012 at 16:00 |
|
Joined: Posts: | December 2011 9 |
|
|
Has anyone been able to get the SC-55 to reliably power on vs rs-232? The command seq they provide is: 100 ms PO 100ms ?P 100ms PZI can't seem to get this to work, I also note that this is a full loop that in theory should turn the unit on and off again, so I've tried removing the last PZ since that's a power toggle, but still no luck. |
|
| OP | Post 2 made on February 18, 2012 at 16:17 |
|
Joined: Posts: | December 2011 9 |
|
|
Please ignore - I figured it out, I had mistakenly entered my as hex 13 instead of decimal 13.
|
|
| Post 3 made on January 10, 2013 at 22:44 |
|
Joined: Posts: | November 2002 47 |
|
|
well, I can't seem to get this to work.
\0xd,0x50,0x4f
|
|
| Post 4 made on January 17, 2013 at 09:51 |
|
Joined: Posts: RC XP: | March 2005 835 310⭐︎ |
|
|
Gamecock fan; as in THE USC?
Why are you sending a hex string? The receivers respond to ASCII for IP and RS-232.
|
They call me the "Thread Killer". Just watch! |
|
| Post 5 made on January 17, 2013 at 15:49 |
|
Joined: Posts: | November 2002 47 |
|
|
yes, "The USC" I am using URC Accelerator (Total Control Editor) and it allows ascii, hex views. I am new to rs-232 programming. I don't know how to type in ascii.Thanks |
|
| Post 6 made on January 17, 2013 at 16:35 |
|
Joined: Posts: RC XP: | March 2005 835 310⭐︎ |
|
|
I haven't looked at that for a while but isn't there an IP/RS-232 driver for an SC-37 in their database? The Power commands haven't changed. Some input source commands, network discretes, and functions are new.
|
They call me the "Thread Killer". Just watch! |
|
| Post 7 made on January 17, 2013 at 16:46 |
|
Joined: Posts: | November 2002 47 |
|
|
yes, there is. It is just the PO command and didn't work. That is when I started digging deeper. edit - Note, I was using IR before and it was working fine. I am exploring RS-232 and ip control now. |
|
| Post 8 made on January 17, 2013 at 17:46 |
|
Joined: Posts: RC XP: | March 2005 835 310⭐︎ |
|
|
The command has to be sent twice in quick succession. Approximately 100ms apart. There may be a repeat setting in the program software. If not do it as a macro. Did any other commands work?
|
They call me the "Thread Killer". Just watch! |
|
| Post 9 made on January 17, 2013 at 20:31 |
|
Joined: Posts: | November 2002 47 |
|
|
Power off worked, I will try more stuff tomorrow
|
|
| Post 10 made on January 18, 2013 at 18:15 |
|
Joined: Posts: RC XP: | March 2005 835 310⭐︎ |
|
|
I tried briefly to setup a Pioneer receiver IP module with Total Control and could not get it to work at all. Never enough time to get back to it.
|
They call me the "Thread Killer". Just watch! |
|
| Post 11 made on January 25, 2013 at 10:02 |
|
Joined: Posts: | November 2002 47 |
|
|
OK, I think the repeat is working most of the time.
Still trying to polish this a bit.
Thanks for help.
|
|
| Post 12 made on August 1, 2013 at 08:05 |
|
Joined: Posts: | April 2012 15 |
|
|
Pioneer always need a wake-up before you can power it on. use it like this:
\x0D
0.5 seconds delay
PO Make sure to put it under Special Macros (device Power Macros) in Accelerator.
Also turn off the energy save crap in the menu of the Pioneer, otherwise the RS-232 port is not listening. If you send me an email I will send you the driver. |
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
