My TSU3000 cannot control my DA-LITE screen. I had no problem with my TS1000. I tried importing the codes from my TS1000 and learning the codes with the TSU3000. I also updated to the latest firmware. The TSU300 appears to learn the codes without any difficulty. I did notice that the original control and the TS1000 send out a very short burst (as displayed on the LED of my wireless keyboard receiver) while the TSU3000 sends out a fairly long string of bursts. The 'down' code as imported from the TS1000 and as learned by the TSU3000 are both:

7000 006D 0000 0008 0011 000D 0010 0002 0017 0003 0003 0003 0003 0003 0003 0003 0002 0003 0000 00BB

Thanks for any help!

It seems that the codes are not learning properly. Try these:

Screen up

0000 006d 0018 0000 0006 011c 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 0906 0006 011b 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 011c

Screen down

0000 006d 0018 0000 0006 011c 0006 011b 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 00bb 0006 08a5 0006 011b 0006 011b 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 00bb 0006 011c

stop

0000 006d 0024 0000 0006 011c 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 011b 0006 08a5 0006 011b 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 011b 0006 08a5 0006 011b 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 00bb 0006 011b 0006 011b 0006 011c

Thank you very much for suggesting the new codes. Unfortunately, they don't seem to work either. I'd certainly be interested if you have any other suggestions.

Your original post said you had the "lastest firmware", but there is a new version since your post. One of their claims is enhanced learning, and our Mr. johnsfine was hoping that they had fixed some of the code learning/transmitting bugs.

Try getting the 2.3.9 firmware and try again.

Barry

I'll try getting the latest firmware. I did notice that the code that mjedwards supplied changed after I pasted it into pronto edit, so I wasn't able to try the actual code that he gave me.

Still no luck!

Try using these codes:

UP: 0000 006C 0000 0015 0003 1EFD 0001 00BE 0004 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 0118 0005 08C2 0005 0118 0005 0118 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 0118 0005 08C2

STOP: 0000 006A 0004 000C 0004 00C1 0005 011E 0005 011E 0005 08F2 0005 011E 0005 00C1 0005 00C1 0005 00C1 0005 00C1 0005 00C1 0005 00C1 0005 00C1 0005 00C1 0005 011E 0005 011E 0005 08F2

DOWN: 0000 006C 0000 000C 0005 0118 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 00BE 0005 0118 0005 00BE 0005 092E

The only "weirdness" I noticed with firmware v2.3.9 was the UP button had to be held for 2 - 3 seconds before the screen would react.

Hope that helps!