I have a customer with an Integra receiver (Model 5.1 I think). I have tried to learn the Zone 2 codes in every way imaginable into a TSU-7000. No go.

So the manufacturer sends me the codes, but I'm not completely sure what format they're in.

For example:

Zone 2 on = D26D 04

Zone 2 off = D26C 47

Can I just cut and paste these codes, or do I have to convert them into Hex somehow??

Thanks,

Dawn

Dawn,
Look-up jonarmstrong or johnfines in the discrete hunter section.
They have the tools and the knowledge to give you a hand.

Typically, when you push the Zone 2 button on the remote, it enables those codes for about 5 seconds, then they revert back. For instance, press Zone 2 then power on within 5 sec and zone 2 comes alive. I just put those codes into an MX800 fine. Have also put them into a Sonance K2 keypad recently.

Pressing the zone 2 button does not itself seem to send a code but only enables a different set of commands from the remote for a short time. This could vary by receiver but I saw this on a 7.4 receiver and a 6.2 receiver in the last 2 weeks.

If it is a 5.1, From what I recall, there is no way to control Zone 2 from the front of the unit. This was the first gen 2 zone unit that would use the primary codeset for zone 2 but ONLY fromt he IR input on the back...... Total pain n the butt...... However, if you happen to be using a MX850 in RF, youcan assign Primary control to go through IR1 to the Front flasher and Zone 2 to go to IR2 to the Back port......
I dont thing the "Zone" button was added rto the remote until the .2's

If the original remote has a 'zone 2' button, include that as the first step of every zone 2 function. If it doesn't, refer back to Impaqt's response.

I did program for MX850 with Integra 5.4 last monday. Zone2 on macro - zone2,0.2,on Zone2 off macro zone2,0.2,standby change inputs macro zone2,0.2,input button . I found all codes in MX editor library (good bless that library!!). Integra 5.1 do not know,sorry , I do not deal with Integra receivers so often.

The original remote has a zone 2 button, and it works just fine. I tried every iteration of learning possible.

The receiver goes into zone 2 mode and stays there until you hit the receiver button again. So, every time you hit, let's say the vol + or Vol - , buttons they work in zone 2 mode until you press the receiver button.

Dawn

I have the file as a .ir file ( Crestron ). Do you have a translator program to change from .ir to what ever the extension is for URC?

Alan

Alan,

I found a file in the libraries here that looks like it will convert the .ir file to Pronto hex.

Please send the file to me!

Thanks,

Dawn

This message was edited by Dawn Gordon Luks on 12/19/04 12:55 ET.

Zone
900A 006D 0000 0001 D26D CC33

Zone 2 On
0000 006D 0044 0002 0156 00AB 0015 0015 0015 003F 0015 0015 0015 0015 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 003F 0015 003F 0015 003F 0015 003F 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 05CC 0156 00AB 0015 0015 0015 003F 0015 0015 0015 0015 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 0015 0015 003F 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 003F 0015 003F 0015 05CC 0156 0055 0015 0E47

Zone 2 Off
0000 006D 0044 0002 0156 00AB 0015 0015 0015 003F 0015 0015 0015 0015 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 003F 0015 003F 0015 003F 0015 003F 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 05CC 0156 00AB 0015 0015 0015 003F 0015 0015 0015 0015 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 0015 0015 0015 0015 003F 0015 0015 0015 0015 0015 0015 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 003F 0015 05F6 0156 0055 0015 0E47

The DTR-5.1 only works thru an external IR receiver plugged into the MR jack.
The DTR-5.2 and 5.3 do not support the discrete power commands.
When sending commands, you must press "Zone" then the command. It is also important to incorporate some delays. A typical Zone 2 macro would look like this:

Zone
1 sec delay
Power On
4 sec delay
Zone
1 sec delay
Tuner


PS. The Zone command hex above was scrubbed with PENG but it works fine.

The "ZONE 2" Button Does not put the remote in Zone 2 mode. It puts the Receiver in "the next code is for Zone 2" mode. All the Commands are the same for Zone 1 and Zone 2..... Its really a terrible design.... The current gen are much better......

Impact,

This is really embarrassing.

The receiver is a 6.5

NOT a 5.1

I'm doing the Pronto programming for a local dealer and the field tech gave me the wrong model number.

Anyone have the zone 2 discrete's??? I need source, vol, and power on and off. :)

Sorry for the mistake.

Dawn

Wow... That a Significant difference.... lol....

I bet the Integra Chad comes stock withthe ZOne 2 codes in it already...

Impact,

The receiver didn't come with a Chad, unfortunately, just the standard remote . Which won't let me learn anything related to Zone 2.

Dawn

The DTR-9.4 ccf in the file section will work fine for you.

If its in fact a 6.5, you can skip the 'power on' command because the input commands turn the unit on(zone 1 and 2)

[Link: remotecentral.com]