|
|
|
Crestron Control Systems Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
PLX3 only displaying the "swirl" logo
| |
|
Topic: | PLX3 only displaying the "swirl" logo This thread has 7 replies. Displaying all posts. |
|
Post 1 made on Monday November 14, 2011 at 19:32 |
bennettavi Active Member |
Joined: Posts: | August 2003 675 |
|
|
We are slowing learning SB using our demo Prodigy gear. I have setup a PMC3, idocv, and PLX3 using system builder and cannot figure out why I only get a Crestron swirl logo on the remote. I have built and rebuilt with the same outcome. I am very new to the programming, so I am sure I have screwed something up, however, we also have the PTL keypad and in a separate SB file we were successful at getting it up and running using the same processor.
I am beginning to wonder if the remote is bad. At the Finish page, all devices and interfaces have green checkmarks and I received no errors. Network ID's are all found and hardware all verified. Are there any "snags" on the PLX3 in SB that I have hit and just can't see? It seems like I would at least get a home page on there or something. Sorry for such a vague issue, but Im not sure how to break it down any more than this. TIA.
Also - Composer yielded the same results...
|
|
Post 2 made on Tuesday November 15, 2011 at 12:10 |
kgossen Super Member |
Joined: Posts: | March 2008 3,026 |
|
|
Under the properties for the remote what devices are checked?
|
"Quality isn't expensive, it's Priceless!" |
|
OP | Post 3 made on Tuesday November 15, 2011 at 15:09 |
bennettavi Active Member |
Joined: Posts: | August 2003 675 |
|
|
Everything is checked like this where the dash is a check:
- Scheduler - Theater -Blue Ray -iPod -Surround Sound AV Receiver
|
|
Post 4 made on Tuesday November 15, 2011 at 16:12 |
kgossen Super Member |
Joined: Posts: | March 2008 3,026 |
|
|
Whats the firmware of the remote? Is it the latest?
|
"Quality isn't expensive, it's Priceless!" |
|
OP | Post 5 made on Tuesday November 15, 2011 at 18:46 |
bennettavi Active Member |
Joined: Posts: | August 2003 675 |
|
|
The remote firmware is up to date, the controller however is not the latest. I'm going to update it first and report back. Thx.
|
|
OP | Post 6 made on Tuesday November 15, 2011 at 18:54 |
bennettavi Active Member |
Joined: Posts: | August 2003 675 |
|
|
Update - just updated the PMC3 firmware to the latest 1.001.0025
Now the " Swirl" is gone but replaced with the phrase , "Invalid built in data"
I rebuilt the system and reuploaded - no change.
|
|
Post 7 made on Wednesday November 16, 2011 at 03:02 |
kgossen Super Member |
Joined: Posts: | March 2008 3,026 |
|
|
I'd talk with TB but it sounds like you could have a brick.
|
"Quality isn't expensive, it's Priceless!" |
|
OP | Post 8 made on Wednesday November 16, 2011 at 10:40 |
bennettavi Active Member |
Joined: Posts: | August 2003 675 |
|
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|