|
|
|
The following page was printed from RemoteCentral.com:
Topic: | MX-900 button press reliability This thread has 188 replies. Displaying posts 76 through 90. |
|
Post 76 made on Tuesday October 3, 2006 at 21:06 |
On October 3, 2006 at 20:50, GregoriusM said...
Easily reproduced on YOUR remote WP. More intermittent and strange on other remotes. Plus, a little different on each person's remote, except perhaps for the firing of the IR on the second button press every time. I don't use IR, so YMMV, but others here like Mitch have said that their remotes act like mine and are easy to reproduce the problem on.
|
|
Post 77 made on Tuesday October 3, 2006 at 22:24 |
JonW747 Active Member |
Joined: Posts: | September 2006 621 |
|
|
If you're not using IR you may very well have an intermittent RF problem somewhere else ... but if the remote isn't detecting the push (not turning on back light?) and doing whatever it does to indicate that it's transmitting a code ... it's probably the same issue.
|
|
Post 78 made on Tuesday October 3, 2006 at 22:45 |
Mitch57 Active Member |
Joined: Posts: | June 2003 722 |
|
|
This problem has nothing to do with RF or IR as far as I can tell. When a button is pressed and the remote registers that button press the LCD screen on LCD buttons will highlight the text next to that button indicating that it has registered the button press. When a button press fails the text on the LCD screen does NOT highlight indicating that the remote did not register the button press.
I haven't done extensive testing on other non LCD buttons but I would be willing to bet that when one of those buttons fail it doesn't register on the LCD screen either. For example, if you press the dedicated "FF" button on the remote it also displays "FF" at the bottom of the LCD screen. When the button press fails you would see no "FF" on the LCD screen.
|
|
Post 79 made on Tuesday October 3, 2006 at 23:30 |
On October 3, 2006 at 22:24, JonW747 said...
If you're not using IR you may very well have an intermittent RF problem somewhere else ... but if the remote isn't detecting the push (not turning on back light?) and doing whatever it does to indicate that it's transmitting a code ... it's probably the same issue. Ooops - I am using IR, I confused IR with RF! Sorry
|
|
Post 80 made on Tuesday October 3, 2006 at 23:33 |
On October 3, 2006 at 22:45, Mitch57 said...
I haven't done extensive testing on other non LCD buttons but I would be willing to bet that when one of those buttons fail it doesn't register on the LCD screen either. For example, if you press the dedicated "FF" button on the remote it also displays "FF" at the bottom of the LCD screen. When the button press fails you would see no "FF" on the LCD screen. That's right, I can verify that.
|
|
Post 81 made on Wednesday October 4, 2006 at 14:30 |
GregoriusM RC Consultant |
Joined: Posts: | December 1999 9,807 |
|
|
Well, I just received a new MX-900 for beta testing a couple of hours ago. I'll let you know how it goes.
|
When ignorance is bliss, ‘tis folly to be wise. |
|
Post 82 made on Wednesday October 4, 2006 at 17:25 |
Pete Harrison Founding Member |
Joined: Posts: | December 1999 147 |
|
|
Greg do you mean a new remote or a new beta software version?
Pete
|
|
Post 83 made on Wednesday October 4, 2006 at 23:50 |
Mitch57 Active Member |
Joined: Posts: | June 2003 722 |
|
|
Greg,
I hope you have better luck then I did. I downloaded the latest Beta update and tested it both last night and tonight and the problem is still there. The failed button press did seem to be less frequent but none the less it still exists. Needless to say I wasn't a happy camper.
Now everytime I pickup my trusty bullet proof MX-700, which I now use in the bedroom, I contemplate about placing the MX-900 under the rear wheel of my Toyota Tundra just prior to backing out of the garage. Do you think URC would cover the damages (or should I say total destruction) under warranty considering the circumstances?
|
|
Post 84 made on Thursday October 5, 2006 at 02:25 |
GregoriusM RC Consultant |
Joined: Posts: | December 1999 9,807 |
|
|
Is there special beta software? Or are you just downloading what is on the URC site? Or just LiveUpdating what you have to 1.10.086, which is the latest update?
I was not sent a link to any beta software.
|
When ignorance is bliss, ‘tis folly to be wise. |
|
Post 85 made on Thursday October 5, 2006 at 23:51 |
Mitch57 Active Member |
Joined: Posts: | June 2003 722 |
|
|
There's special Beta Software that you will have to get from URC if they are willing to give it out. I'm not sure what URC's policy is on this but I asked Eric if he would let me use it for testing purposes only.
You won't be able to get any live updates with the currently released software. Only with the beta version. When a new beta version is available for download I will download and test it and then post my findings here.
Stay tuned!
|
|
Post 86 made on Friday October 6, 2006 at 14:02 |
Surf Remote Loyal Member |
Joined: Posts: | July 2001 5,958 |
|
|
Seems to be working well with the latest beta update.
|
www.SurfRemoteControl.comTHX-certified video calibrator and contributing writer, ProjectorReviews.com |
|
Post 87 made on Friday October 6, 2006 at 15:34 |
GregoriusM RC Consultant |
Joined: Posts: | December 1999 9,807 |
|
|
It still needs some work, Mike.
|
When ignorance is bliss, ‘tis folly to be wise. |
|
Post 88 made on Friday October 6, 2006 at 18:32 |
Mitch57 Active Member |
Joined: Posts: | June 2003 722 |
|
|
Yes. I agree. There's still some more fine tuning that needs to be done to get it just right.
|
|
Post 89 made on Sunday October 8, 2006 at 21:37 |
skynyrdfan Active Member |
Joined: Posts: | March 2006 666 |
|
|
I have noticed the same problem... Don't have it with the 850 I hope Eric is looking into this problem... if they do not fix it soon I will have to switch back to the 850 which I hear are going to be in every retailer soon. maybe even costco...
|
|
Post 90 made on Monday October 9, 2006 at 00:19 |
GregoriusM RC Consultant |
Joined: Posts: | December 1999 9,807 |
|
|
The engineers are working on it and a new beta should be out shortly. The last beta improved things quite a bit.
|
When ignorance is bliss, ‘tis folly to be wise. |
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|