Your Universal Remote Control Center
RemoteCentral.com
RTI Control Systems Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
CB-8 pass 232?
This thread has 8 replies. Displaying all posts.
Post 1 made on January 18, 2010 at 13:49
B
bencn
Long Time Member
Joined:
Posts:
January 2010
24
Hi there,

It says in the manual that the connecting block passes IR to control system, but doesn't say anything about 232.

Does it also pass 232?


Here's my routing:

KP4 with 232 programmed buttons + IR programmed buttons
going to CB-8

Also a KP3-V with 232 programmed buttons
going to CB-8

CB-8 to RP-6
RP-6 232 out to different devices.


I'm assuming it must, but have learned never to assume anything


Cheers

Post 2 made on January 18, 2010 at 14:37
F
FASTLs
Long Time Member
Joined:
Posts:
October 2004
480
Do you mean a K4 and an RK-3?

If so, Yes, you can do RS232 and controll a device!

FASTLS

OP | Post 3 made on January 18, 2010 at 15:10
B
bencn
Long Time Member
Joined:
Posts:
January 2010
24
You mean through the CB-8 connecting block right?
OP | Post 4 made on January 18, 2010 at 15:33
B
bencn
Long Time Member
Joined:
Posts:
January 2010
24

Another way of saying it..

Following the blue line from K4 -> CB-8 -> RP-6
Will the RP-6 output the 232 code I assigned in
Integration Designer for the K4?

I'm almost certain it will, but just making sure.

Post 5 made on January 18, 2010 at 15:36
F
FASTLs
Long Time Member
Joined:
Posts:
October 2004
480
Yes, It can run the RS232 as long as you use the CM232.

FASTLS

OP | Post 6 made on January 18, 2010 at 15:43
B
bencn
Long Time Member
Joined:
Posts:
January 2010
24
Awesome. Thanks!
Post 7 made on January 18, 2010 at 18:35
A
anyhomeneeds
Super Member
Joined:
Posts:
December 2007
4,149
On January 18, 2010 at 14:49, bencn said...
Hi there,

It says in the manual that the connecting block passes IR to control system, but doesn't say anything about 232.


The problem you are having is thinking that the commands are being held in the keypads. Thay aren't, not when you are using a processor like the RP-6. All the commands are stored on the RP-6, and the only thing being transmitted through the CB-8 are trigger codes for the processor.

Now, in stand-alone scenario, a standard IR connecting block will NOT pas 232 codes, for that you will have to use a CPB-1.

"You can't fix stupid."
Post 8 made on January 19, 2010 at 01:40
R
RTI Installer
Super Member
Joined:
Posts:
RC XP:
March 2002
3,321
24⭐︎
On January 18, 2010 at 19:35, anyhomeneeds said...
The problem you are having is thinking that the commands are being held in the keypads. Thay aren't, not when you are using a processor like the RP-6. All the commands are stored on the RP-6, and the only thing being transmitted through the CB-8 are trigger codes for the processor.

Now, in stand-alone scenario, a standard IR connecting block will NOT pas 232 codes, for that you will have to use a CPB-1.


This is the correct answer
Never Ignore the Obvious -- H. David Gray
OP | Post 9 made on January 20, 2010 at 10:40
B
bencn
Long Time Member
Joined:
Posts:
January 2010
24
Right on, thanks!

Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.