 |
 |
|
|
Philips Pronto NG Family Forum - View Post
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
| Topic: | X10 IR direct commands This thread has 6 replies. Displaying all posts. |
|
| Post 1 made on Wednesday April 28, 2004 at 14:50 |
MTRX Founding Member |
Joined:
Posts: | October 2001
43 |
|
|
Hi, I'm using a configuration file that I downloaded on this website, that has all X10 commands and all X10 direct commands (like On1, On2, Off1, Off2 etc.). For some reason when I use thos commands on my pronto tsu 3000 they also get executed, my pronto confirms with one beep that button was pressed however no signal is being sent to my IR543.
I tried using built in X10 commands that come with Pronto, and used something like this (Ch1, Delay (0.1), PwrOn, Delay(0,1)) and that works fine for me, however it it a bit slow, if I want to turn lets say Litght1 and then Light2 it doesn't work, I have to wait for couple of seconds untill the last commands finishes execution.
Any ideas where I can get working X10 direct commands? Or maybe I can make them myself?
|
|
| Post 2 made on Wednesday April 28, 2004 at 14:59 |
Dave Houston RF Expert |
Joined:
Posts: | October 2001
1,521 |
|
|
It takes about 1/2 second for the IR543 to transmit a command to the powerline. It is deaf to further inputs while its doing that so you'll need about a 1/2 second delay between the unit and function commands.
|
|
| OP | Post 3 made on Wednesday April 28, 2004 at 15:14 |
MTRX Founding Member |
Joined:
Posts: | October 2001
43 |
|
|
That is fine I noticed that. However problem that I have is that I can't use direct commands at all, they don't always work even if I add 1/2 second delay and push puttons slowly... Does any one has working X10 direct commands?
|
|
| Post 4 made on Wednesday April 28, 2004 at 15:30 |
Dave Houston RF Expert |
Joined:
Posts: | October 2001
1,521 |
|
|
There are no DIRECT commands but only macros. The macros need the 1/2 second or longer delays between each command.
|
|
| Post 5 made on Wednesday April 28, 2004 at 16:18 |
mburwen Founding Member |
Joined:
Posts: | August 2001
1,185 |
|
|
Where did you get the codes? I first loaded all the codes from Codegen, but I had problems with the bright/dim commands. I then used these two commands from Paul Antico's file (do a search on ir543 in the TSU3000 file section), and I also used that file's X-10 command macros which call for a .2 second delay between the unit number and operational commands and TWO operational commands with no delay between. Now all works perfectly.
|
|
| OP | Post 6 made on Thursday April 29, 2004 at 15:23 |
MTRX Founding Member |
Joined:
Posts: | October 2001
43 |
|
|
I downloaded system file from (Ludovic Hauduc's Quick Switching PCF), that file has X10 direct commands. I'm not sure how they were generated, but they don't always work... I will try Paul Antico's file...
thanks!
|
|
| OP | Post 7 made on Thursday April 29, 2004 at 15:32 |
MTRX Founding Member |
Joined:
Posts: | October 2001
43 |
|
|
Just downloaded Paul Antioc's file but for some reason my ProntoEdit NG software would not open it, says "This file type cannot be opened by this editor". My verison is 2,0,6,0. I think this is a latest one. I'm using TSU 3000. Not sure why it woul not open..
Please help...
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
