Your Universal Remote Control Center
RemoteCentral.com
General Pro Remotes Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Use IRSrutiniser with Keene remote codes
This thread has 4 replies. Displaying all posts.
Post 1 made on October 29, 2026 at 04:57
K
kdp99
Long Time Member
Joined:
Posts:
RC XP:
April 2004
191
298⭐︎
I have got an HDMI switch cheap without a remote. I have found what I think/hope are the codes here in Keene format.

I need to turn them into proton hex. I wondered if IRsecutiniser would do the job, I have used it but am a no expert, I had a quick look and it did not jump out to me.

If will do it can nay kind person point me in the right direction.

Many thanks

Post 18

[Link: remotecentral.com]

Post 2 made on October 30, 2026 at 10:26
Barf
Long Time Member
Joined:
Posts:
RC XP:
August 2013
390
346⭐︎
I have never heard about "the Keene format" before. So I went to their website https://www.info.keene-electronics.co.uk/ and downloaded their pack [Link: info.keene-electronics.co.uk] . That zip file contains, among other things, a pdf document API documentation.pdf. On page 7, it says:
This code format is a simple ASCII text representation of the IR code. The first character in the string is a capital “K”
followed by a space. The next four characters are the frequency expressed as a 2-digit hex number and number of
bursts of carrier including the lead in burst followed by a space.
The remaining blocks of four ASCII characters are the times in uS in hex of the burst then no burst. All are separated
by a space.
The final value is always 2000 and is the lead out no-burst time.
That's all there is! Is that enough for you? If not just tell me...
OP | Post 3 made on October 30, 2026 at 13:19
K
kdp99
Long Time Member
Joined:
Posts:
RC XP:
April 2004
191
298⭐︎
Thanks so much, not quite there for me. If I new the protocol 'data', i.e what to put into IR scrutiniser I could generate all 255 codes and have an experiment, but I am not that versed in the world of IR speak, I stop at using a Hex code.

Can you shed anymore light

Post 4 made on October 30, 2026 at 15:45
Barf
Long Time Member
Joined:
Posts:
RC XP:
August 2013
390
346⭐︎
I could not help myself, so I wrote a preliminary Keene decoder for IrScrutinizer. I posted the decodes in the linked thread. Do you have more Keene-signals to decode, or are the Matrix switcher commands all you need?
OP | Post 5 made on October 30, 2026 at 16:40
K
kdp99
Long Time Member
Joined:
Posts:
RC XP:
April 2004
191
298⭐︎
THANKS SO MUCH

Only just did a spot check with one code and it works (was not 100% sure they were correct), took 2 presses just to make me worry !

This as been a real help

Thanks again !

I shall now add all the codes and have a play !

You are a start !

Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.