 |
 |
|
|
Consumer Electronics Control Wiki
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
The following is an archive of information recorded for the Motorola MXv5 IR Wiki entry. This version was created by eoghan on Friday April 22, 2016 at 19:44. (Original Entry)
| | | Brand: | Motorola |
| Device Type: | FibreOP Bell Aliant remote |
| Model/Series: | MXv5 IR |
| Model Year: | 2015/2016 |
| Information: | [Link: bellaliant.ca] |
| Configurations: | Search the file area |
| | | | | | | Notes: | Do you have FibreOP with Bell Aliant and a new MXv5 remote that will only turn on and off your TV? Good news with these instructions you can make the FirbreOP remote more useful.
Are all device (TV, DVD, and AUX) functions on the Bell Aliant FibreOP MXv5 remote seem to be locked to the STB button.
When I press TV then [OK] or {EXIT] the function is sent to the STB
When I press TV [Left], [Right], [Up], [Down] it is always sent to STB. This does not make for a very helpful universial remote.
I cannot find a way to program the MXv5 remote for my TV but I did find a way to bypass the functions that are locked to STB.
I put the remote into learning mode and then programed the buttons I need.
Place MXv5 into Learning Mode:
Place your original remote control nose-to-nose 2" apart with the MXv5
Press Device (TV)
Press and hold the [SETUP] button until the LED flashes twice.
Enter the code 9-7-5. The LED should flash twice.
Select the device (TV) onto which you wish to learn a signal.
Press a [Button] to learn the signal on the MXv5. The LED begins blinking rapidly.
Hold down the key on your original remote that you want to learn until the LED flashes twice.
Repeat with all buttons (see list below) (skip this step if you are only learning 1 key)
Press and hold the [SETUP] button to save
There is a limit of how many codes can be learned… if you need to clear one button
Clear one learned button:
Press and hold the [SETUP] button until the LED flashes twice.
Enter the code 9-7-6. The LED should flash twice.
Press the button to clear. The device key will flash.
Press the button to clear again. The device key will flash twice.
Reset Remote to Factory defaults:
Press and hold the [SETUP] button until the LED flashes twice.
Enter the code 9-7-7. Device will flash 4 times
Remote is now set to default |
| |
|
|
|
Input Options
| | | Infrared: | Yes |
| IR Input Jack: | No |
| Radio Frequency: | No |
| RS-232 (Serial): | No |
| Network IP: | No |
| Bluetooth: | No |
| USB: | No |
| DC Trigger: | No |
| | | Output Ports
| | | IR Output Jack: | No |
| RS-232 Output: | No |
| DC Trigger: | No |
| |
| |
|
Discrete Codes
| |
| Power: | No - Workaround |
| Inputs: | N/A |
| Sound Modes: | N/A |
| Picture Modes: | N/A |
| Screen Modes: | N/A |
| |
| Delays/Timings
| | | Power On: | Unknown |
| Switch Inputs: | Unknown |
| Inter-command: | Unknown |
| |
|
|
|
| Important Codes & Commands |
Buttons I have found helpful:
OK, Exit, Menu, Up, Down,
Left, Right, (remember when face to face opposite side of remote)
Chanel +/- → Chanel +/- rPi (Page up/down)
Return → Apps rPi (Contextual menu)
Green → Recorded TV rPi (Video Menu)
Yellow → On Demand rPi (Music Menu)
Chanel +/- → Chanel +/- rPi (Page up/down)
Sleep → Delete
Tools → Options
|
|
|
|
|
|
|
