Your Universal Remote Control Center
RemoteCentral.com
RS-232 & IP Control Forum - View Post
Previous section Next section Previous page Next page Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Page 1 of 2
Topic:
Yamaha RX-V3900 RS232 Commands?
This thread has 23 replies. Displaying posts 1 through 15.
Post 1 made on Monday April 20, 2009 at 23:05
Davis W
Long Time Member
Joined:
Posts:
April 2003
31
I am looking for RS-232 commands for the Yamaha RX-V3900/RX-V7 receiver. Yamaha has changed their RS232 command protocol for these receivers so the old commands don't work.

Yamaha released a spreadsheet that details the commands and has a tool for building them but the tool is broken in the older release (which I have). I am hoping that someone has the updated spreadsheet with the working command tool.

Thanks!
Post 2 made on Tuesday April 21, 2009 at 02:47
Casentis
Long Time Member
Joined:
Posts:
November 2008
10
I found these commands:

RS232
Baud: 9600
Parity: N
Data Bits: 8
Stop Bits: 1


0,1,*,PUT,System(Power_Control(Power=On)),*\x0D\x0A
0,1,*,PUT,System(Power_Control(Power=Standby)),*\x0D\x0A
Post 3 made on Tuesday April 21, 2009 at 03:58
gopronto
Senior Member
Joined:
Posts:
April 2008
1,453
i have a prontofile with most of them in there, but make sure you have firmware version 1.07, PM me if youwant the file
Pronto still one of the best Wi-Fi Remotes,
www.ikonavs.co.nz and [Link: axiumcontrol.com] Axium Control
Post 4 made on Tuesday April 21, 2009 at 08:18
hdtvluvr
Long Time Member
Joined:
Posts:
September 2002
402
On April 20, 2009 at 23:05, Davis W said...
I am looking for RS-232 commands for the Yamaha RX-V3900/RX-V7 receiver. Yamaha has changed their RS232 command protocol for these receivers so the old commands don't work.

Yamaha released a spreadsheet that details the commands and has a tool for building them but the tool is broken in the older release (which I have). I am hoping that someone has the updated spreadsheet with the working command tool.

Thanks!

What is the date of the spreadsheet file you have?
OP | Post 5 made on Tuesday April 21, 2009 at 19:40
Davis W
Long Time Member
Joined:
Posts:
April 2003
31
Thanks guys for the replies. gopronto I will pm you as I would like to get a copy of your file. I am using firmware 1.07.

hdtvluvr, the excel spreadsheet that I have is version 1.0 from August 22nd, 2008. It has a "compile error in hidden module 1" error that pops up every im you open it. Because of this the command builder function doesn't work. I read in another post here that Yamaha fixed the issue in a later release of the file but I haven't been able to locate it.

Thanks!
Post 6 made on Wednesday April 22, 2009 at 01:10
gopronto
Senior Member
Joined:
Posts:
April 2008
1,453
you need version 1.01.
Pronto still one of the best Wi-Fi Remotes,
www.ikonavs.co.nz and [Link: axiumcontrol.com] Axium Control
Post 7 made on Thursday April 23, 2009 at 13:15
stjoh
Long Time Member
Joined:
Posts:
April 2009
16
I've got the original version with the error. Anybody willing to share the latest version?
OP | Post 8 made on Thursday April 23, 2009 at 18:11
Davis W
Long Time Member
Joined:
Posts:
April 2003
31
I can't figure out why Yamaha advertises serial control as a feature and then makes it so darn hard to find the protocol docs.
Post 9 made on Friday April 24, 2009 at 16:03
gopronto
Senior Member
Joined:
Posts:
April 2008
1,453
Please note there is a bug in the RS232 codes for the 3900, z9,z7

the volume up for Zone 2 and 3 does not work but i have a work around if any one needsd it..

the bug is, up for both zones , goes down !
Pronto still one of the best Wi-Fi Remotes,
www.ikonavs.co.nz and [Link: axiumcontrol.com] Axium Control
Post 10 made on Thursday April 30, 2009 at 06:42
gopronto
Senior Member
Joined:
Posts:
April 2008
1,453
I also have the cursor controls now Too :)
Pronto still one of the best Wi-Fi Remotes,
www.ikonavs.co.nz and [Link: axiumcontrol.com] Axium Control
OP | Post 11 made on Thursday May 7, 2009 at 11:12
Davis W
Long Time Member
Joined:
Posts:
April 2003
31
GoPronto,

Thanks again for all the info!
Post 12 made on Friday May 8, 2009 at 17:33
gopronto
Senior Member
Joined:
Posts:
April 2008
1,453
no problem a cople of more work arounds

Menu

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85847B))),137
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853B44))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85443B))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85413E))),129


Cursor Up

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A859D62))),137
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A852B54))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85304F))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85354A))),129


Cursor Down

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A859C63))),137
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A852C53))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85314E))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853649))),122


Cursor Left

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A859F60))),137
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A852D52))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85324D))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853748))),122


Cursor Right

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A859E61))),137
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A852E51))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85334C))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853847))),122


Enter

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85DE21))),144
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A852F50))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85344B))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853946))),122


Return(SUB MENU)

Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85AA55))),144
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853C43))),129
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A853F40))),129
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85423D))),129


Display(PLAY INFO)
Main Zone
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A85C23D))),144
Zone 2
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A8536C9))),137
Zone 3
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A8537C8))),137
Zone 4
0,1,49,PUT,System(Remote_Signal(Receive(Code=7A8538C7))),137
Pronto still one of the best Wi-Fi Remotes,
www.ikonavs.co.nz and [Link: axiumcontrol.com] Axium Control
Post 13 made on Sunday May 17, 2009 at 14:05
Frico855
Lurking Member
Joined:
Posts:
May 2009
4
On April 22, 2009 at 01:10, gopronto said...
you need version 1.01.

Cant seem to find it on the net.. or maybe Im just bad at searching ;)
Post 14 made on Friday May 22, 2009 at 01:40
gopronto
Senior Member
Joined:
Posts:
April 2008
1,453
sent it to your hotmail account :)
Pronto still one of the best Wi-Fi Remotes,
www.ikonavs.co.nz and [Link: axiumcontrol.com] Axium Control
Post 15 made on Thursday July 9, 2009 at 02:53
Tom Light
Long Time Member
Joined:
Posts:
December 2006
229
I have the most important commands working now, only with the tuner presets i have some troubles...

Found the commands here:
[Link: awe-europe.com]

First command i tryed was:

0,1,*,PUT,Tuner(Preset(Preset_Sel=A1)),*\x0D\x0A

than i did some variations on it, nothing worked.

Does somebody has an example code ??
Page 1 of 2


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse