|
|
 |
|
The following page was printed from RemoteCentral.com:
|
Good RTI RS232 commands for DirecTV?
| |
|
| Topic: | Good RTI RS232 commands for DirecTV? This thread has 16 replies. Displaying posts 1 through 15. |
|
| Post 1 made on Friday March 27, 2009 at 22:03 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
I was told that the H21 RS232 commands in the RTI library are bad, does anybody have good commands to share with me?
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| Post 2 made on Sunday March 29, 2009 at 12:24 |
thefish Founding Member |
Joined:
Posts: | September 2001
1,721 |
|
|
|
| Post 3 made on Sunday March 29, 2009 at 12:26 |
thefish Founding Member |
Joined:
Posts: | September 2001
1,721 |
|
|
|
| OP | Post 4 made on Monday March 30, 2009 at 11:51 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
Yeah, I know the codes need to be changed to hex. I am asking if anybody (mega232list, RTI master) has updated the flies so that they are the correct commands.
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| OP | Post 5 made on Monday April 6, 2009 at 23:53 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
Well, I finally did this install today and the codes in the RTI master 232 library worked fine. I didn't have to go into the properties and conveert to hex like mentioned above.
And Glack hooked me up with the channel commands too! Thanks alot! These commands are awsome, so fast and reliable. I used them to replace all of my favorite channels and XM scrolling list macros. I didn't think the channel commands were going to work with the H21, I thought it was only for the pro model DVR. Anyway, I am glad I tried them because it made my day.
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| Post 6 made on Sunday April 19, 2009 at 11:10 |
Mr. Burns Long Time Member |
|
|
I’m really looking forward to controlling the DirecTV boxes rs-232. I got the RTI lib but how do I do the direct channel jump? This is huge for the XM list!
|
The least expensive short term solution usually turns out to be the most expensive long term solution. |
|
| OP | Post 7 made on Sunday April 19, 2009 at 22:53 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
Check your email
I feel it is my duty to pass these commands on to you because glack sent them to me.
PS they work great in the scrolling list too! (for your XM)
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| Post 8 made on Monday September 28, 2009 at 13:27 |
ahentertainment Long Time Member |
Joined:
Posts: | March 2008
39 |
|
|
I just ordered the iogear usb adapter for my client with four of these boxes. Can someone send me the direct channel codes as this will save me a lot of time with his favorites. Thanks.
|
|
| OP | Post 9 made on Monday September 28, 2009 at 22:37 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
On September 28, 2009 at 13:27, ahentertainment said...
I just ordered the iogear usb adapter for my client with four of these boxes. Can someone send me the direct channel codes as this will save me a lot of time with his favorites. Thanks. You will need one USB adapter per DTV box. What is your email address? I will send you the direct channel commands.
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| OP | Post 10 made on Monday September 28, 2009 at 23:12 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
Hey guys I just noticed that these commands are in the RTI master 232 library.
Go to: DirecTV/Satellite Receiver/Channel Direct
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| Post 11 made on Thursday October 1, 2009 at 10:13 |
ahentertainment Long Time Member |
Joined:
Posts: | March 2008
39 |
|
|
I have reset the box twice (HR21-100 and H21-100) and still have no control over them. The light on the GUC232A is not on. Anyone have any suggestions?
|
|
| Post 12 made on Thursday October 1, 2009 at 10:37 |
thefish Founding Member |
Joined:
Posts: | September 2001
1,721 |
|
|
Are you using a null modem?
Make sure firmware is up to date on the DTV box
Post your power on and channel 202 strings.
|
|
| Post 13 made on Thursday October 1, 2009 at 10:53 |
ahentertainment Long Time Member |
Joined:
Posts: | March 2008
39 |
|
|
Yep I have the null modem adapter. The current version on the direct tv box is ox34c
I am going through the gpio port #8 and have the software set to CM Port 8. Right now the only commands I put on the remote were ch + and ch -.
Is the light supposed to be on on the guc232a?
|
|
| Post 14 made on Thursday October 1, 2009 at 17:57 |
Don O'Brien Long Time Member |
Joined:
Posts: | August 2002
237 |
|
|
Try to disconnect power from the unit, insert the USB adapter, power up the receiver and see if you get a response after the unit has booted up completely. Try this hex command FA A5 00 01 A1 and see if you get the "Info" screen up on your display. Either that or it sounds like you may have a bad USB to serial adapter.
|
|
| Post 15 made on Thursday October 1, 2009 at 19:23 |
thefish Founding Member |
Joined:
Posts: | September 2001
1,721 |
|
|
Is the light supposed to be on on the guc232a? No, not that I have ever seen. Not sure what to tell you, it's always worked for me no problem. Did you rewrite the RS232 commands so they are in Hex?
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
