 |
 |
|
|
RTI Control Systems Forum - View Post
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
| Topic: | RTI RF issues This thread has 5 replies. Displaying all posts. |
|
| Post 1 made on Tuesday March 25, 2008 at 09:41 |
inflamarus Long Time Member |
Joined:
Posts: | March 2008
30 |
|
|
So I have a standard RP-6/RM-433/T2-C RTI setup; the problem is as soon as I hookup the 433 it begins to flash red and green with reckless abandon. This would seemingly indicate that the 433mhz band is saturated. As I understand it you cannot change the frequency that RTI operates under; has anyone run into this before/have a workaround or solution for it. Thanks.
|
Lets not bicker and argue about who killed who. |
|
| Post 2 made on Tuesday March 25, 2008 at 09:42 |
ceied Loyal Member |
Joined:
Posts: | February 2002
5,753 |
|
|
i have seen this problem as well... it was mis wired.
|
Ed will be known as the Tiger Woods of the integration business, followed closely with the renaming of his company to "Hotties A/V". The tag line will be "We like big racks and tight holes"... |
|
| Post 3 made on Tuesday March 25, 2008 at 13:31 |
Benford AV Active Member |
Joined:
Posts: | August 2007
714 |
|
|
Check all your wiring, then watch the LED while you move the RM433 to possible different mounting locations. Sometimes 6 inches in any direction will clear-up alot of the interference.
Also, the RTI system will ignore any non-RTI communication (red LED), so I wouldn't go crazy trying to eliminate everything until you acctually get the remote running and test to see if you even have any communication issues at all.
|
The Soundwave www.the-soundwave.comB&W, Classe', Rotel, Paradigm, Integra, Denon, Audioquest, RTI, Niles, Pioneer Elite, Bell'O |
|
| Post 4 made on Tuesday March 25, 2008 at 20:11 |
I have run into a situation where in three separate systems in three separate homes I was having a ton of RF problems. I wasted a ridiculous amount of time troubleshooting them. Eventually had to have RTI replace every piece in all three of the different systems (3 T4's, 3 RP-6's, 5 RM-433's). Once I put all the new stuff in, everything worked great. So, if standard RF troubleshooting doesn't work, don't rule out bad equipment.
Last edited by mfbarnes
on March 25, 2008 23:06.
|
|
| Post 5 made on Tuesday March 25, 2008 at 21:30 |
ErikS Active Member |
Joined:
Posts: | July 2003
699 |
|
|
Try downloading new firmware into the T2-C. Or redownload if it is the current. We had a T4 that was sending out constant signal with no buttons pressed causing all the other remotes not to work and as soon as we redid the update, problem solved.
|
|
| Post 6 made on Wednesday March 26, 2008 at 00:17 |
thefish Founding Member |
Joined:
Posts: | September 2001
1,721 |
|
|
I had this happen today in a rack. Turned off the cable box, flashing stopped. I'll move the RM433 farther away.
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
