|
|
|
The following page was printed from RemoteCentral.com:
Topic: | t-4 rp 1 issues This thread has 11 replies. Displaying all posts. |
|
Post 1 made on Saturday February 16, 2008 at 11:52 |
zinon Founding Member |
Joined: Posts: | September 2001 621 |
|
|
I ran into this strange issue today with a small RTI system ( T-4 and a single RP 1)
I swapped out a defective Pioneer DVD player for a new Marantz player. I changed all of the DVD ir codes in the program. then loaded them into the T-4 and RP 1 . Tested the remote and nothing worked. The rp1 is not responding to the rf commands.
I then delete the rp1 1 from the program and try IR only and it works perfect. Then I add the rp1 to the program and its not working again. I the notices that if the rp1 antenna is a couple of inch's away from the t4 it works. This system was working with out any flaws before today's download We are using touch screen designer version 5.10.
Thanks Zinon
|
|
Post 2 made on Saturday February 16, 2008 at 15:13 |
cassidycaid Founding Member |
Joined: Posts: | October 2001 256 |
|
|
Did you unplug the USB cable from the RP1?
|
Scientific method refers to the body of techniques for investigating phenomena, acquiring new knowledge, or correcting and integrating previous knowledge. |
|
Post 3 made on Saturday February 16, 2008 at 18:44 |
stereoman4 Select Member |
Joined: Posts: | December 2007 1,966 |
|
|
are you powering directly to the rp1 or the connecting block. If it didn't work close to the antenna i would say your new upload wasn't with the default in RF trigger codes.
|
www.goinnovativeaudiovisual.comCedia certified installer ISF Certified 'It's not how many times you get knocked down but it's how many times you get back up and go forward" |
|
OP | Post 4 made on Saturday February 16, 2008 at 20:48 |
zinon Founding Member |
Joined: Posts: | September 2001 621 |
|
|
On February 16, 2008 at 15:13, cassidycaid said...
Did you unplug the USB cable from the RP1? Yes I did unplug the USB cable. also the RP1 is powered directly . Zinon
|
|
Post 5 made on Saturday February 16, 2008 at 21:00 |
ceied Loyal Member |
Joined: Posts: | February 2002 5,753 |
|
|
i say you have the remote not send rf and ir only
|
Ed will be known as the Tiger Woods of the integration business, followed closely with the renaming of his company to "Hotties A/V". The tag line will be "We like big racks and tight holes"... |
|
Post 6 made on Saturday February 16, 2008 at 21:05 |
cpchillin Select Member |
Joined: Posts: | September 2007 2,239 |
|
|
Make sure the remote isn't in standalone mode!
|
Who says you can't put 61" plasmas up on cantilever mounts using toggle bolts? <---Thanks Ernie ;) |
|
OP | Post 7 made on Saturday February 16, 2008 at 21:06 |
zinon Founding Member |
Joined: Posts: | September 2001 621 |
|
|
Ed
It is in rf mode.It will send rf only a few inch. I brought the rp1 back with me and I will swap it out with the one in my house and see if it is defective. Zinon
|
|
Post 8 made on Saturday February 16, 2008 at 22:03 |
Tom Ciaramitaro Loyal Member |
Joined: Posts: | May 2002 7,967 |
|
|
The weird part is that the change in DVD players brought it about.
I had my own T4 work like the one you described - works within 2 feet of the RP1. The M2 downstairs works fine, so I don't suspect the RP1 at all. Just got it back from RTI and haven't tried it yet.
I have gotten goofed up with adding an RP1 after the fact (set up at first with no processor) for no apparent reason. Setting default/RF trigger codes, yet if I check properties on some device buttons, they are still standalone.
By testing at home, you may have determined the problem already.
You could carry one of your other remotes to the jobsite to test the RP1 there.
Just for grins, check the properties on some of those buttons.
|
There is no truth anymore. Only assertions. The internet world has no interest in truth, only vindication for preconceived assumptions. |
|
OP | Post 9 made on Sunday February 24, 2008 at 06:01 |
zinon Founding Member |
Joined: Posts: | September 2001 621 |
|
|
Update, It was a defective RP-1 This is strange because it was working perfectly until I downloaded the new program to it. Thanks Zinon
|
|
Post 10 made on Sunday February 24, 2008 at 07:52 |
A/Vjunkie Long Time Member |
|
|
On February 24, 2008 at 06:01, zinon said...
Update, It was a defective RP-1 This is strange because it was working perfectly until I downloaded the new program to it. Thanks Zinon I had a bad RP-1 a month agao.......and RTi said they are very, very far and few between! Are alot of you guys seeing bad ones?
|
I once thought I had mono for an entire year, it turned out I was just really bored - Wayne's World |
|
Post 11 made on Sunday February 24, 2008 at 09:17 |
cassidycaid Founding Member |
Joined: Posts: | October 2001 256 |
|
|
I had a bad RK1 a few weeks back...
Apropos of absolutely nothing, did you know that if you reverse the signal and ground wires for the rj-45 connector in the RK1 that the unit will power up and program like normal, but will not output any IR when hooked up, even if you realize your mistake later and fix the connector pin outs...
|
Scientific method refers to the body of techniques for investigating phenomena, acquiring new knowledge, or correcting and integrating previous knowledge. |
|
Post 12 made on Sunday February 24, 2008 at 10:30 |
pesci Senior Member |
Joined: Posts: | August 2006 1,211 |
|
|
On February 24, 2008 at 07:52, A/Vjunkie said...
I had a bad RP-1 a month agao.......and RTi said they are very, very far and few between!
Are alot of you guys seeing bad ones? YEP!!!! I had 2 Bad... i had a rp1 working for about a yr went back cuz he had a BAD T2C, when i fransfered comm, rp1 fried somehow!!!!! go figure, rti at it again!!!!!
|
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|