|
|
|
The following page was printed from RemoteCentral.com:
Topic: | RP6 High Out Reduction This thread has 8 replies. Displaying all posts. |
|
Post 1 made on Monday February 4, 2008 at 18:07 |
Just an Installer Long Time Member |
Joined: Posts: | March 2007 175 |
|
|
Hi all. I have an install using an RP6 to control 6 DirecTV receivers. I need one output for RS232 control of a projector, so I need to use the high out for one of the sat receivers. What is the easiest way to cut the signal level coming out of the high output, without using a connecting block? A bit too much for a single emitter to handle all on it's lonesome; I fried one last year, at the end of 90+ feet of Cat5. I thought there would have been enough loss over that distance...but that's what we get for thinking. Trying to keep the cost down, otherwise I'd just rather use a connecting block. This bar owner is already having a hard time deciding between an M2 (don't even get me started), and a T2+. Any and all help and suggestions always appreciated.
As an aside, how's your candidate doing, or going to do tomorrow?
Perhaps a can of worms better left unopened?
|
Listen, think, THEN speak. |
|
Post 2 made on Tuesday February 5, 2008 at 00:19 |
cheesehead22 Long Time Member |
|
|
Yes that can of worms is better left unopened as this is a A/V forum, not anything else.
|
Don't read my answer. Someone else will go into great detail as to why I am wrong rather than answer the original question... |
|
Post 3 made on Tuesday February 5, 2008 at 01:33 |
RTI Installer Super Member |
Joined: Posts: | March 2002 3,320 |
|
|
Just hook up a minimum of 3 emitters to the high out, that should be enough resistance to get you by on the cheep
|
Never Ignore the Obvious -- H. David Gray |
|
Post 4 made on Tuesday February 5, 2008 at 08:57 |
FRR Advanced Member |
Joined: Posts: | June 2003 918 |
|
|
The RP6 manual says to use the the small jumper cables that are provided with the RP6 (i.e. don't plug directly into the RP6). I failed to observe this detail once and managed to fry the attached emitter.
|
Logic is a systematic method of coming to the wrong conclusion with confidence. |
|
Post 5 made on Tuesday February 5, 2008 at 09:32 |
cpchillin Select Member |
Joined: Posts: | September 2007 2,239 |
|
|
FRR if you are talking about the pigtails then they are used to take out the power that is feeding out from the regular 3.5mm outputs, which is used for RS232 and other modules. He is talking about the phoenix connector High Out that is right beside the power and signal in. But yes if you don't use the pigtails you could easily fry IR emitters if they aren't seated properly in the connector or when plugging them in with the RP6 on.
|
Who says you can't put 61" plasmas up on cantilever mounts using toggle bolts? <---Thanks Ernie ;) |
|
Post 6 made on Tuesday February 5, 2008 at 10:00 |
markrubin Founding Member |
Joined: Posts: | February 2002 919 |
|
|
If your budget allows, add a 100 ohm resistor in series with the + lead of the emitter connected to the high output port
|
|
OP | Post 7 made on Tuesday February 5, 2008 at 10:56 |
Just an Installer Long Time Member |
Joined: Posts: | March 2007 175 |
|
|
On February 5, 2008 at 10:00, markrubin said...
If your budget allows, add a 100 ohm resistor in series with the + lead of the emitter connected to the high output port This is what I was looking for. And within budget! Any particular wattage of resistor? I think I have some 1/2 watt ones around, just need to check what the impedance is. Thanks a bunch.
|
Listen, think, THEN speak. |
|
OP | Post 8 made on Saturday February 9, 2008 at 15:37 |
Just an Installer Long Time Member |
Joined: Posts: | March 2007 175 |
|
|
On February 5, 2008 at 10:00, markrubin said...
If your budget allows, add a 100 ohm resistor in series with the + lead of the emitter connected to the high output port Thanks again to markrubin. Resistor worked great, got me by on the cheap. The rs232 control of the Epson projector was a bit finicky at the end of 84 feet of cat5, though. Some commands worked flawlessly, the rest did not work at all. Adding a slight delay between characters took care of the problem. Odd that some would work but not all, though.
|
Listen, think, THEN speak. |
|
Post 9 made on Saturday February 9, 2008 at 21:14 |
Ernie Bornn-Gilman Yes, That Ernie! |
Joined: Posts: | December 2001 30,104 |
|
|
100 ohms, 1/4 watt should do. Higher wattages okay, too. To compare, the Xantech blocks use a 470 ohm resistor; the Xantech amplified blocks use 470 ohms for regular, and 100 ohms for high output.
|
A good answer is easier with a clear question giving the make and model of everything. "The biggest problem in communication is the illusion that it has taken place." -- G. “Bernie” Shaw |
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|