 |
 |
|
|
RTI Control Systems Forum - View Post
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
|
Can anyone share an RP6 with Marantz RS232?
| |
|
| Topic: | Can anyone share an RP6 with Marantz RS232? This thread has 10 replies. Displaying all posts. |
|
| Post 1 made on Wednesday January 9, 2008 at 09:50 |
drobaina Long Time Member |
Joined:
Posts: | December 2007
332 |
|
|
Anyone out there have a system file with an RP6 already loaded up with Marantz AVR RS232 codes? Just being lazy and not wanting to have to type it all out.
Thanks!
|
|
| Post 2 made on Wednesday January 9, 2008 at 20:44 |
Springs Super Member |
Joined:
Posts: | May 2002
3,238 |
|
|
Use an IR direct Input and save the $75 and the time typing. IR input via a Direct IR wire $2.
|
|
| Post 3 made on Thursday January 10, 2008 at 12:59 |
dfrey Lurking Member |
Joined:
Posts: | February 2007
9 |
|
|
Yes I have a file, but honestly, Springs is correct. I was surprised at the IR depth of the Marantz codes, including all discretes and direct setting of volume level (which is why I originally went with RS-232 for an SR8002). Wish I had checked Marantz's IR remote codes prior.
In any event, the next RS232 device I get, the CM232 comes off the Marantz and on that device.
David
|
|
| Post 4 made on Wednesday February 6, 2008 at 23:27 |
Timber Long Time Member |
Joined:
Posts: | November 2004
156 |
|
|
David,
Where did you find the IR codes for the 8002? I did not locate on the mega list.
|
|
| Post 5 made on Thursday February 7, 2008 at 00:16 |
cdouglass Long Time Member |
Joined:
Posts: | February 2008
166 |
|
|
On January 10, 2008 at 12:59, dfrey said...
Yes I have a file, but honestly, Springs is correct.
I was surprised at the IR depth of the Marantz codes,
including all discretes and direct setting of volume level
(which is why I originally went with RS-232 for an SR8002).
Wish I had checked Marantz's IR remote codes prior.
In any event, the next RS232 device I get, the CM232 comes
off the Marantz and on that device.
David Most IR codes are available but sometimes you may still need RS232. For example the new SR7002 has HDMI out 1 and 2 but no IR codes are given, however RS232 codes are available.
|
|
| Post 6 made on Thursday February 7, 2008 at 05:40 |
Springs Super Member |
Joined:
Posts: | May 2002
3,238 |
|
|
Just curious... what are you using those codes or settings for? (Hdmi out 1 and 2)
|
|
| Post 7 made on Thursday February 7, 2008 at 07:45 |
cdouglass Long Time Member |
Joined:
Posts: | February 2008
166 |
|
|
On February 7, 2008 at 05:40, Springs said...
Just curious... what are you using those codes or settings
for? (Hdmi out 1 and 2) The SR7002 can send audio and video to 2 monitors but not at the same time. The client can now watch all his video sources from the main room in his bedroom via HDMI and utilizing the RS232 code "HDMI OUT CH2". Also when sending an HDMI signal to the mst bdrm TV, the "HDMI Audio Mode" should be set to "THROUGH" so that it can receive audio. The SR8002 is different it can be used as a matrix switch for 2 simultaneous monitors.
|
|
| Post 8 made on Thursday February 7, 2008 at 10:02 |
cdouglass Long Time Member |
Joined:
Posts: | February 2008
166 |
|
|
On January 9, 2008 at 09:50, drobaina said...
Anyone out there have a system file with an RP6 already
loaded up with Marantz AVR RS232 codes? Just being lazy
and not wanting to have to type it all out.
Thanks! Something for you to think about....use IR codes so that you don't have to type them all out, then use RS232 when IR codes are not available. By using this combo you will also have discreets that are not available with RS232.
|
|
| Post 9 made on Thursday February 7, 2008 at 11:35 |
tgrugett Select Member |
Joined:
Posts: | August 2004
1,850 |
|
|
|
| Post 10 made on Friday February 8, 2008 at 07:04 |
cdouglass Long Time Member |
Joined:
Posts: | February 2008
166 |
|
|
On January 9, 2008 at 09:50, drobaina said...
Anyone out there have a system file with an RP6 already
loaded up with Marantz AVR RS232 codes? Just being lazy
and not wanting to have to type it all out.
Thanks! The new 6.0 software has all the codes, pretty cool. Just watch out, you may run into a bug that prevents you from finishing your project.
|
|
| Post 11 made on Saturday February 9, 2008 at 08:27 |
cdouglass Long Time Member |
Joined:
Posts: | February 2008
166 |
|
|
On February 7, 2008 at 05:40, Springs said...
Just curious... what are you using those codes or settings
for? (Hdmi out 1 and 2) Srings, as it turned out I went back to the SR7002 and found the HDMI Out Ch 1 & 2 to have discreet IR. It was not documented correctly on the spreadsheet from the Marantz website. So far no RS232 had to be used for the current project. When the XP8 with 2-way start shipping out, that will be a different story.
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
