Your Universal Remote Control Center
RemoteCentral.com
Sony Remote Controls Forum - View Post
Previous section Next section Previous page Next page Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Page 3 of 9
Topic:
SONY RECEIVERS: Changing Command Mode to AV1 (or AV2)
This thread has 120 replies. Displaying posts 31 through 45.
Post 31 made on Thursday May 4, 2006 at 07:00
JReb
Lurking Member
Joined:
Posts:
May 2006
2
Never mind...I finally found directions on page 34 of the manual. It's not listed in the TOC or index, just kind of hidden there in case anyone else is looking for the same info.
Post 32 made on Monday July 17, 2006 at 22:22
adamsadow
Lurking Member
Joined:
Posts:
July 2006
2
Ron,

Your ifnormation looks great!! I was wondering if I can change the command code for the DAV-C450 unit that uses the RM-SS450 remote?

Thank you very much!

Sincerely,
Adam
[email protected]
Post 33 made on Monday July 17, 2006 at 23:19
edmund
Elite Member
Joined:
Posts:
April 2002
13,469
On July 17, 2006 at 22:22, adamsadow said...
Ron,

Your ifnormation looks great!! I was wondering
if I can change the command code for the DAV-C450
unit that uses the RM-SS450 remote?

Thank you very much!

Sincerely,
Adam
[email protected]

Sorry, but no.
Post 34 made on Tuesday July 18, 2006 at 09:46
adamsadow
Lurking Member
Joined:
Posts:
July 2006
2
edmund,

Thank you for the response. Just to clarify, my unit/remote's command code cannot be changed?

Thank you again,
Adam
[email protected]
Post 35 made on Tuesday July 18, 2006 at 09:56
edmund
Elite Member
Joined:
Posts:
April 2002
13,469
Right, your sony dream system neither uses AV1 or AV2 codesets, it use one of its own.
Post 36 made on Saturday August 19, 2006 at 16:05
Hawkseyes
Lurking Member
Joined:
Posts:
August 2006
4
Any updates on changing AV2 to AV1 on Sony STR-DG600 to get it to work with a VIP 622 remote?

Hawk
Post 37 made on Wednesday September 6, 2006 at 10:26
SonyBoy
Lurking Member
Joined:
Posts:
September 2006
1
Great Post. I figured out that this procedure also works for the HT-7000DH & HT-7550DH (aka STR-K7000). Now I can use my Sony universal remote, RM-V503.

On the Receiver:
1. Turn off receiver
2. Press and hold the INPUT button
3. Press the power button to toggle AV modes
4. The display will read out the current mode, i.e., AV1 or AV2.

Works great. Thanks
OP | Post 38 made on Thursday September 14, 2006 at 11:56
Ron Aronson
Super Member
Joined:
Posts:
June 2002
3,967
On August 19, 2006 at 16:05, Hawkseyes said...
Any updates on changing AV2 to AV1 on Sony STR-DG600
to get it to work with a VIP 622 remote?

Hawk

On September 6, 2006 at 10:26, SonyBoy said...
Great Post. I figured out that this procedure also works
for the HT-7000DH & HT-7550DH (aka STR-K7000). Now I
can use my Sony universal remote, RM-V503.

On the Receiver:

1. Turn off receiver
2. Press and hold the INPUT button
3. Press the power button to toggle AV modes
4. The display will read out the current mode, i.e., AV1
or AV2.

Works great. Thanks

I have added the procedures for both components to this thread.

Last edited by Ron Aronson on October 10, 2006 14:16.
Post 39 made on Monday September 25, 2006 at 14:15
kingwr12
Lurking Member
Joined:
Posts:
September 2006
3
For the DG600 I would try the same technique as the DG800. On the unit, turn on the unit while holding "Input Mode" to toggle between AV1 and AV2. On the remote, press and hold "Remote Setup" until the light on, press 1 for AV1 or 2 for AV2, then enter. Light flashes then goes out.

If I change my system to AV1, can anyone point me to a component page for my pronto that will work on AV1?
OP | Post 40 made on Tuesday October 10, 2006 at 14:41
Ron Aronson
Super Member
Joined:
Posts:
June 2002
3,967
On September 25, 2006 at 14:15, kingwr12 said...
For the DG600 I would try the same technique as the DG800.
On the unit, turn on the unit while holding "Input Mode"
to toggle between AV1 and AV2. On the remote, press and
hold "Remote Setup" until the light on, press 1 for AV1
or 2 for AV2, then enter. Light flashes then goes out.

If I change my system to AV1, can anyone point me to a
component page for my pronto that will work on AV1?

Thanks for the info. I have updated this thread accordingly.

I don't know anything about a Pronto, but the standard Sony component code will work with AV1, so you can either use the Receiver page, or do whatever makes the Pronto assign a receiver to another component screen.
Post 41 made on Friday October 27, 2006 at 20:04
cheapbeersucks
Lurking Member
Joined:
Posts:
October 2006
1
Well I just got off of chat with SONY tech support and he straight up told me that it was impossible to run a de995 reciever with the av 2100 remote. And you mr aronson singlehandedly proved him wrong.. You rock!
Post 42 made on Friday December 8, 2006 at 14:57
robyn
Lurking Member
Joined:
Posts:
December 2006
3
Just want to say thanks. Maybe I knew this the last time I set up a Sony receiver - but that was a long time ago! By the way - I have the Sony STR-DG1000. You can change both the receiver - and the remote - and the instructions are on pages 38-9 of the user manual. Now everything works with my old Sony Remote Commander AV-2100. Robyn
OP | Post 43 made on Monday December 18, 2006 at 19:13
Ron Aronson
Super Member
Joined:
Posts:
June 2002
3,967
I have added the STR-DG1000 (thanks, robyn) and updated the procedures for the STR-DG600, STR-DG800 and the HT-7000DH and HT-7550DH (STR-K7000 receiver and RM-AAP012 remote) in this thread.
Post 44 made on Monday January 8, 2007 at 17:16
messmaker
Lurking Member
Joined:
Posts:
January 2007
1
I tried it on my STR DG500 and it worked like a charm. (same procedure as 600 model)
Thank you Ron
Post 45 made on Thursday January 18, 2007 at 10:43
nycazn79
Lurking Member
Joined:
Posts:
January 2007
1
Thank you very much for this forum/topic. It saved me time and $$$ instead of returning my STR-DG1000 for a Denon AVR-2307ci just to control my volume with my S/A 8300HD stock remote. As a new project, now I have to go home and try re-program my Harmony 880 to AV1 codes as a backup (since it is programed with AV2 codes).
Find in this thread:
Page 3 of 9


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse