|
|
|
HDTV Reception Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
DirecTV even transponders out on 1...
| |
|
Topic: | DirecTV even transponders out on 1 receiver only!! This thread has 8 replies. Displaying all posts. |
|
Post 1 made on Saturday January 1, 2000 at 18:50 |
proceba2 Historic Forum Post |
|
|
i have DirecTV with 2 hughes receivers. the one setup downstairs is working fine, but the one in my bedroom is not locking onto any of the even numbered transponders. the channel banner come up for those stations, but then the bottom of the screen states "searching for satellite etc, blah, blah." why would only 1 receiver have that problem? HELLLPPP!!!
|
|
OP | Post 2 made on Saturday January 1, 2000 at 23:42 |
You are using a dual lnb sate arn't you. It will be required for it to work. You can not just split the cable with a spliter like you can with with normal cable. Hope this helps
|
|
OP | Post 3 made on Sunday January 2, 2000 at 12:16 |
proceba2 Historic Forum Post |
|
|
scott -- yes it is a dual LNB. its just ive never had this problem until a few days ago, which is why i cant seem to figure out the source of the problem. could it possibly be one on the LNBs and not a receiver problem?
|
|
OP | Post 4 made on Sunday January 2, 2000 at 19:07 |
check the cable connections on the dual lnb. one may have come loose. are there any splices? check to see if the conection has come apart
|
|
OP | Post 5 made on Sunday January 2, 2000 at 19:51 |
proceba2 Historic Forum Post |
|
|
wayne -- i checked all of the cables and connections on my box outside and everything looks fine there. off hand the cables going to the LNB at the dish looked ok, but i didnt really get in there to check...ill try that next. thanks.
|
|
OP | Post 6 made on Monday January 3, 2000 at 00:09 |
wayne Historic Forum Post |
|
|
swap the ouyout of the lnbs and see if the problem moves
|
|
OP | Post 7 made on Monday January 3, 2000 at 13:06 |
Mike M Historic Forum Post |
|
|
Another possibility to check here are the connections and cables. OIt is conceivable that a loose connection or bad cable could cause thsi. also if your line is surge suppressed try bypassing the surge suppressor to see if it is the culprit. This is not likely but easy enough to check
|
|
OP | Post 8 made on Tuesday January 4, 2000 at 09:39 |
biily c Historic Forum Post |
|
|
hi guys...if its not a simple cable or a connector problemthat u can detect, then i suggest as follows:dis-connect the rcvr that works good, and hook-it up in place of the bad rcvr , at the same spot....if that rcvr works ok, then the other rcvr is ng, if it dont work ok, u DEFINITELY have a cabling or connector problem feeding that location ONLY....good luck billy c
|
|
OP | Post 9 made on Tuesday January 4, 2000 at 10:59 |
proceba2 Historic Forum Post |
|
|
over the last day or 2 all the channels seem to be working fine again, even though some of the signals are as low as 79. go figure. but i will keep an eye on it to see if it is a recurring problem. thanks for all replies.
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|