The following page was printed from RemoteCentral.com:
Device code needed
This thread has 5 replies. Displaying all posts.
|Post 1 made on Friday May 29, 2015 at 13:43|
I am trying to recode a *Universal Electronics* remote (the standard remote for Rogers/Cisco digital tuners),
one device I have is a Technics digital processor(SH-AC500D) that works hand in hand with a Technics receiver/amp.
finding the codes for the receiver are a breeze (they are already in place) but finding the codes for this processor are not,
I came across (here in this website) an entry that displays ALL the sub codes for this device but I haven't seen the master code for the device,
can anyone lend some assistance?
thx, Steve[Link: remotecentral.com]
|Post 2 made on Friday May 29, 2015 at 15:10|
If by Master you mean setup code, then these are the only UEI codes that use Panasonic protocol, device 160, subdevice 18 and are used in the other codes you linked that have any chance of being in a cable remote. Even so, it's a pretty rare code.
Audio  0521
If you use a Panasonic Combo protocol with variable subdevice and intend to program individual EFCs, then you have many more possibilities:
Audio  1288, 1308,1518,1763,1764,0115,1309,1350,1363,1509,1765,1779,1807,2967,
Video/DVD  1834,1905,1907,1908,1909,1910
(Prefix with the number in [brackets] if your remote takes 5 digit codes. Codes in bold are the most common.)
The only Rogers/Cisco DTA remote I can find accepts only TV codes and thus has none of the above built in. If you can post a pic or model number, I can give you a more definitive answer.
|OP | Post 3 made on Friday May 29, 2015 at 23:21|
The universal remote that controls multiple devices used by Rogers for the Cisco 4642HD tuner is this...[Link: google.com]
the model # of the remote I have is...1056B01....the remote is manufactured by Universal Electronics
a few of of the codes you displayed...1308, 1309,1518 are the setup code for the Technics receivers, which are different than that for the processor
|Post 4 made on Saturday May 30, 2015 at 02:01|
That's good news-- the Atlas 1056B01 is an excellent remote and it is possible to make it work with the SH-AC500D. However, it does require doing a little more work than just assigning a setup code. You'll need to enter a 5 digit EFC for each function.
First decide which buttons you want to use for the functions. You already have the receiver set up on the Audio device button. You may want to redefine some of the buttons in Audio mode so that the processor will respond to them instead of the receiver. Or perhaps you'll want to use a different device button (I'll use VCR as an example) for the processor. Then:
A) Redefine the VCR button to change its type from Video to Audio. (Skip this step if you're going to use the Audio button for both the receiver and processor.)
1) Press Setup until 2 blinks
2) Enter 992 (should see 2 blinks)
3) Press Audio
4) Press VCR (should see 2 blinks)
B) Assign Setup code 1308 to VCR (Skip this step if you're going to use the Audio button for both the receiver and processor.)
1) Press Setup until 2 blinks
2) Enter 1308 (should see 2 blinks. If it doesn't blink twice, then step A didn't work)
C) Assign EFCs for each function to the buttons of your choosing. Note that you can't assign EFCs to the device buttons, Setup, or Master Power.1) Press Setup until 2 blinks2) Enter 994 (should see 2 blinks)
3) Press Setup (don't hold it)
4) Enter the 5 digit EFC (44862 for Vol+)
5) Press the button which should send this command (e.g. the Volume up button) You should see 2 blinks.
Repeat step C for each of the functions below.
volume + 44862
volume - 44990
balance left 44894
balance right 45022
Surround Up 44814
Surround Down 44942
Dig Space On 44854
EQ On/Flat 44854
EQ SFP 44854
Snd Field Press 44854
power on 44870
power off 44998
Dig Space Pr 44923
EQ SFP 44923
level + 44827
level - 44955
digital 1 60779
digital 2 60907
digital 3 60683
Vid CD Power 60819
VCR 1 60739
dr comp 60719
Cinema Re-EQ 60847
Dolby Pro Logic 60695
Channel Select 60903
delay + 60713
EQ Effect Up 60713
delay - 60841
EQ Effect Down 60841
Center Up 60745
Center Down 60873
Edited to include more functions.
Last edited by 3FG on May 30, 2015 10:56.
|OP | Post 5 made on Saturday May 30, 2015 at 17:11|
daaaaaamn......that's a lot of single entries...lol
I'm sure that all of them won't go in (not enough buttons on the Atlas)
will try to get the important ones...
thx very much,
|Post 6 made on Tuesday June 2, 2015 at 17:58 |
If you're willing to spend $8 on an interface cable, you can load all those codes in one shot by simply loading a file and without pressing any buttons at all.[Link: ebay.com]
As you can see, 1308 is
the correct code (as are all the others I posted) according to the pronto hex you found. The brands listed in the manual are irrelevant in this case. The important thing is finding a setup code with the compatible protocol and other details which I did, and for which 3FG was kind enough to provide all the individual EFCs.
||Before you can reply to a message...|
You must first register
for a Remote Central user account - it's fast and free! Or, if you already have an account, please login
Please read the following:
Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace
. For information on how to advertise your service or product click here
. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.