Your Universal Remote Control Center
RemoteCentral.com
General Consumer Remotes Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Need manual for old GEMINI remote control
This thread has 11 replies. Displaying all posts.
Post 1 made on Saturday August 18, 2007 at 11:11
jauris
Lurking Member
Joined:
Posts:
August 2007
5
I need manual or any info for old GEMINI remote control ( see picture at this link:
).
Post 2 made on Saturday August 18, 2007 at 14:29
edmund
Elite Member
Joined:
Posts:
April 2002
13,273
OP | Post 3 made on Saturday August 18, 2007 at 16:19
jauris
Lurking Member
Joined:
Posts:
August 2007
5
Sorry edmund, but this manual don't match to my remote control ( no RCL key on this remote).I guess, my remote is much older than GEMINI Quick20.
Post 4 made on Saturday August 18, 2007 at 16:49
edmund
Elite Member
Joined:
Posts:
April 2002
13,273
you don't have a model #, can't make out anything from that picture. did you try the file section here:


[Link: remotecentral.com]


Or the instructions and codes are for zenith:

[Link: remotecentral.com]


would this remote have those rockers in the battery compartment?

[Link: remotecodelist.com]

Last edited by edmund on December 6, 2012 20:11.
OP | Post 5 made on Saturday August 18, 2007 at 18:20
jauris
Lurking Member
Joined:
Posts:
August 2007
5
Sorry edmund, but those links weren't helpful. I've tried these files, and my remote don't have rookers in the battery compartment.It has switch up on the right side for TV-VCR-CATV. I can upload better resolution picture, if it would be helpful.
Post 6 made on Tuesday September 25, 2007 at 03:11
alan.1
Lurking Member
Joined:
Posts:
September 2007
2
i need a code for gemini remote :-)
well i dont know what this section means, it just says three lines so, here are three lines as asked lol
Post 7 made on Sunday December 30, 2007 at 12:07
spacekitty
Lurking Member
Joined:
Posts:
December 2007
1
I also have a Quik20 and found this thread while searching for codes myself.
Maybe this will help. It's for the Quik20 but does not refer to any RCL key:

Quik20 Universal Remote Control Programming Codes

1.Press and HOLD "PWR" and "MUTE" until the red indicator turns on (3-4 sec)
2.Select the type of device you are programming by pressing the TV, VCR, CTV or AUX key.
3.Aim the Quik20 at the device you are trying to program and press the red "PWR" key.
If your device turns off, press the approprate device mode key again (TV,VCR,AUX) to lock in the brand code and exit.
4. If the device doesn't respond, press the VOL"+" key once to advance to the next brand code. Now press the PWR key again. Remember to immediately lock in your code when the component turns OFF by pressing the proper mode key.

This search method could take quite a while, so be patient!!
Post 8 made on Wednesday May 14, 2008 at 17:24
Big_Ford_Country
Lurking Member
Joined:
Posts:
May 2008
1
After pressing all kinds of button combos, I helld the learn button for about ten seconds and it lit up. I found the smart 15 manual on this site and punched in codes for many VCRS and the 3 TVS I have. I got the Zenith to work.
Basically hold the learn button about 4- 10 seconds the teach and learn buttons will flash , press the correct power button you want to program, look up the code on the smart 15 manual, input the 3 digit code and enter (ENT). it should stop flashing for a second and the learn light will hold then it flashs again. Hold learn for a couple seconds longer the lights go out and try the code. Repeat with another code if not working. Repeat for other functions. I have the same remote as the original poster
Post 9 made on Wednesday May 21, 2008 at 08:56
bitza75
Lurking Member
Joined:
Posts:
May 2008
1
For Jauris:
I also have this remote, and wanted to use it as a replacement. Couldn't find the manual anywhere. Yesterday, I found this forum, and saw your request, followed the links to no avail. guess what? today is my lucky day! I finally found the manual this morning, seaching for another document! The manual's name is: "multi-brand controller MAC15/20" and I can scan it for you. As you request is rather old, please first confirm you still need it! I believe you only need the "learning part" of this remote? This is only two pages. hope I am not too late!

Last edited by bitza75 on May 21, 2008 09:10.
Post 10 made on Wednesday May 21, 2008 at 23:12
Daniel Tonks
Wrangler of Remotes
Joined:
Posts:
October 1998
28,035
At minimum, I'm sure others would appreciate the manual - you can forward scans to me and I'll put it up in the file area here.
OP | Post 11 made on Wednesday June 11, 2008 at 05:58
jauris
Lurking Member
Joined:
Posts:
August 2007
5
To bitza75:
Thank you very much for your reply!My request of GEMINI remote control manual is still actual.Please upload everythimg you have about it to my e-mail (view my profile).Thanx!
OP | Post 12 made on Wednesday June 11, 2008 at 06:16
jauris
Lurking Member
Joined:
Posts:
August 2007
5
For Big_Ford_Country:
The code entering procedure you've described seems to work.Now i'm trying to find code for my old Philips TV, as i know it needs simple RC-5 code.I tried codes 112 and 113 from Gemini Smart15 manual, but these codes don't match.Maybe you know, how to get to the "autosearch" mode?Thanx!


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse