Your Universal Remote Control Center
RemoteCentral.com
One For All & Radio Shack Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
6011 back from UEI customer service, but...
This thread has 4 replies. Displaying all posts.
Post 1 made on Wednesday January 19, 2005 at 22:01
marcmag
Lurking Member
Joined:
Posts:
January 2005
2
I sent my remote into the Customer Service shop, along with my JVC/Sirius remote, since they did not have a code for it. I appreciated the addition of the 1811 code for my JVC/Sirius receiver. I think a JP1 plug was installed, too.

However, despite my asking that it be put on the SAT key, the JVC/Sirius was instead placed on the RCVR-AMP key. Now, I cannot control the Technics tuner-amp that I need to use in order to hear the JVC/Sirius.

Can I move the 1811 code (or its equal) to the SAT key for the JVC and resume using the RCVR-AMP key for the Technics? Or is there a sequence I can put into the the remote to use the SAT or the HOME THEATRE key to control the Technics?

Since the remote now has the JP1 pins (I'm pretty sure they weren't there before) is my only solution to buy the cable and move/remap the device? And if I do, will I lose the JVC/Sirius code they put in?

I've decided not to put the Technics code on the RCVR-AMP key until I hear from UEI or get feedback from this forum.
Post 2 made on Wednesday January 19, 2005 at 23:06
ofafan
Founding Member
Joined:
Posts:
May 2002
249
First: DO NOT put anything else on that RCVR/AMP key yet. Good call on that.
Next: With jp1 you could download the entire contents of the remote as it now is and very easily change the device. But you don't have that, so...

Your next impulse was correct, you can control the Technics with the SAT key. It's called a Device Mover function, and is documented in your "manual" (you know, that cheesy little piece of paper they put in there.
Jim
Post 3 made on Wednesday January 19, 2005 at 23:53
edmund
Elite Member
Joined:
Posts:
April 2002
13,600
Nothing will happen to the upgrade code if you program over it with technics setup code. You want the SAT key to have code 1811, here's how:

1. press and hold SET for two blinks
2. enter 9-9-2
3. press AUD
4. press SAT

5. press SAT
6. press and hold SET for two blinks
7. enter 1-8-1-1
OP | Post 4 made on Thursday January 20, 2005 at 22:07
marcmag
Lurking Member
Joined:
Posts:
January 2005
2
I followed the latter advice, moved the RCVR-AMP (AUD) function over to SAT and loaded the Technics code on to RCVR-AMP. Success: now the Sirius/JVC is on SAT and the Technics RCVR is on RCVR-AMP.

Now, I'll read up on the Advanced Codes to install the Technics Surround-Sound Processor to the remote, something I had not had the nerve to try before. Thanks to both of you for help and encouragement.
Post 5 made on Friday January 21, 2005 at 04:43
ofafan
Founding Member
Joined:
Posts:
May 2002
249
On 01/19/05 23:06 ET, ofafan said...
First: DO NOT put anything else on that RCVR/AMP
key yet. Good call on that.

Aargh. I have to stop doing late-night posts. I lose my mind and forget basics.

Of course the code is in the EEPROM, and can be assigned to another device. UEI loaded it just like one of us from the jp1 group would have. I feel stupid for telling you differently.

Glad all is working out so far.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse