 |
 |
|
|
URC's Consumer Remotes Forum - View Post
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
|
need Integra Dtr 10.5 zone 3 codes
| |
|
| Topic: | need Integra Dtr 10.5 zone 3 codes This thread has 8 replies. Displaying all posts. |
|
| Post 1 made on Thursday April 20, 2006 at 14:31 |
HUM BARS Long Time Member |
Joined:
Posts: | February 2005
37 |
|
|
I know some one here has already gone threw the trouble of learning these codes
I need inputs, vollume level and discreet zone 3 on and off
thanks in advance
Andy
|
|
| Post 2 made on Thursday April 20, 2006 at 16:25 |
Tom Ciaramitaro Loyal Member |
Joined:
Posts: | May 2002
7,969 |
|
|
Are you an installer? The website for support has it all.
|
There is no truth anymore. Only assertions. The internet world has no interest in truth, only vindication for preconceived assumptions. |
|
| OP | Post 3 made on Thursday April 20, 2006 at 17:12 |
HUM BARS Long Time Member |
Joined:
Posts: | February 2005
37 |
|
|
Yes I'm an installer and I looked, DTR10.5 zone 3 codes are not on the support website
|
|
| Post 4 made on Friday April 21, 2006 at 01:51 |
Glackowitz RC Moderator |
Joined:
Posts: | May 2002
3,793 |
|
|
Try the codes for another receiver..like a 7.6 zone 3 controls...most of the codes sets are similar
|
There's no worse feeling than that millisecond you're sure you are going to die after leaning your chair back a little too far. |
|
| Post 5 made on Friday April 21, 2006 at 02:04 |
Tom Ciaramitaro Loyal Member |
Joined:
Posts: | May 2002
7,969 |
|
|
There is an Excel spreadsheet and it's all there. I looked. My copy is a year old. Hex format.
|
There is no truth anymore. Only assertions. The internet world has no interest in truth, only vindication for preconceived assumptions. |
|
| Post 6 made on Friday April 21, 2006 at 02:07 |
Glackowitz RC Moderator |
Joined:
Posts: | May 2002
3,793 |
|
|
I was using mine from September yesterday and saw zone 3 stuff for the 7.6..I didnt even look at the 10.5 stuff
Hum Bars...better check again, there are tabs on the bottom of the sheet for different command sets
|
There's no worse feeling than that millisecond you're sure you are going to die after leaning your chair back a little too far. |
|
| OP | Post 7 made on Friday April 21, 2006 at 11:25 |
HUM BARS Long Time Member |
Joined:
Posts: | February 2005
37 |
|
|
looks like it's all there I'm a big fat stupid head
thanks for the tabs tip I'll open my eyes wider next time
|
|
| Post 8 made on Friday April 21, 2006 at 11:27 |
Tom Ciaramitaro Loyal Member |
Joined:
Posts: | May 2002
7,969 |
|
|
Don't be so hard on yourself. Your mother still thinks you are a good boy.
|
There is no truth anymore. Only assertions. The internet world has no interest in truth, only vindication for preconceived assumptions. |
|
| Post 9 made on Thursday June 1, 2006 at 07:09 |
SMatson Long Time Member |
Joined:
Posts: | October 2004
38 |
|
|
I am not a dealer and am looking for IR code help for my two DTM 5.3's. I have changed the remote ID on one to gain independent IR control, but my remote is having trouble learning the volume control for the new ID'ed remote. Could these files help me find the right code? Please send if possible.
scottmatsonATcoxDOTnet
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
