Your Universal Remote Control Center
RemoteCentral.com
URC's Consumer Remotes Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Recieved an MX-800 as a gift and need some help
This thread has 3 replies. Displaying all posts.
Post 1 made on Friday September 28, 2007 at 14:16
louthewiz1
Long Time Member
Joined:
Posts:
June 2007
30
I was given an mx-800 but it does not have the default screen names etc,I do have an mx-500 but this is a completly different remote and I need some help.
I downloaded the software and registered and got the latest software but I want to restore thr remote back to factory default because it has all types of names that don't match my components.
Post 2 made on Friday September 28, 2007 at 20:08
8ate8
Advanced Member
Joined:
Posts:
November 2005
778
Just start programming it in the software. When you download to the remote, everything will be replace with what you program in the software.
OP | Post 3 made on Friday September 28, 2007 at 21:53
louthewiz1
Long Time Member
Joined:
Posts:
June 2007
30
I also have hex codes for an extron scaler dvs-204 but I don't know how to import these codes into the mx-800..

Signal Timing
2
IR Remote Control Hex codes and Signal Timing • Signal Timing
Carrier Frequency = 38 KHzDuty Ratio = T1/Tc = 1/3TcT19ms9ms0.56ms4.5ms2.5msTfTfLead CodeCustom CodeCustom CodeData CodeData Code1st FrameRepeat Code0.56msBit “0”1.125ms0.56msBit “1”2.25msBit DescriptionC0C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7Tf : 102msThe transmitted waveform as long as a key is depressed.Frame Interval : Tf
Hex codes
1
IR Remote Control Hex codes and Signal Timing • Hex Codes
123489101112131415161718192021222324252627282930313233343536373839404142434445657
Figure 1. — Corresponding
button numbers
To find the hex data codes for your individual Extron IR Remote Control, match your button positions with those in figure 1, then look up the corresponding button number in the Hex Data Code Table, (e.g. button # 16 [arrowed] has the hex code 0F).
N Your remote will not have all the buttons shown.
The figure covers the button combinations of all Extron
IR Remote models available.
HEX Data Code T
able
(Refer to figure 1 for button number)
Button # HEX Code
1 00
2 01
3 02
4 03
5 04
6 05
7 06
8 07
9 08
10 09
11 0A
12 0B
13 0C
14 0D
15 0E
16 0F
17 10
18 11
19 12
20 13
21 14
22 15
23 16
24 17
Button # HEX Code
25 18
26 19
27 1A
28 1B
29 1C
30 1D
31 1E
32 1F
33 40
34 41
35 42
36 43
37 44
38 45
39 46
40 47
41 48
42 49
43 4A
44 4B
45 4C
Signal timing with code positions are shown below
Post 4 made on Saturday September 29, 2007 at 10:29
1ziggi1
Long Time Member
Joined:
Posts:
September 2006
410
Quite a bit different from the Harmony 880. I can see why you wanted to trade. The Harmony is a cute remote but pretty crappy programming. Also the remote should have been reset to factory defaults. If it wasn't just hold down the main and stop buttons until the menu pops up to reset it.

Last edited by 1ziggi1 on September 29, 2007 10:36.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse