Your Universal Remote Control Center
RemoteCentral.com
Discrete Code Hunter Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Onkyo TX-NR414
This thread has 8 replies. Displaying all posts.
Post 1 made on Thursday April 26, 2012 at 08:03
Trunk-Slammer -Supreme
Loyal Member
Joined:
Posts:
November 2003
7,402
None of the older codes seems to work.

Anyone have a source for Onkyo codes?
Post 2 made on Thursday April 26, 2012 at 10:29
MacrossZero
Active Member
Joined:
Posts:
March 2009
594
Have you checked the Remote ID on the receiver?

■ Remote ID
`1, 2, or 3
When several Onkyo components are used in the same 
room, their remote ID codes may overlap. To differentiate 
the AV receiver from other components, you can change 
its remote ID from “1”, to “2” or “3”.
Note
• If you do change the AV receiver’s remote ID, be sure to change 
the remote controller to the same ID (see below), otherwise, you 
won’t be able to control it with the remote controller.
Changing the remote controller’s ID
1 While holding down RECEIVER, press and hold 
down Q SETUP until the remote indicator lights 
(about 3 seconds).
2 Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice
Do or Do not, There is no Try.
OP | Post 3 made on Friday April 27, 2012 at 09:50
Trunk-Slammer -Supreme
Loyal Member
Joined:
Posts:
November 2003
7,402
Haven't tried that but I don't see that it should/would make a difference.

The OEM remote works, but it only has a toggle on/off and I need the discrete on/off commands for a URC MX900 remote.

Again:

The URC database doesn't have this AVR listed, and the codes that are in the database will not work.

I checked on the Onkyo support forums and got a reply stating that Onlyo doesn't have the TX-NR414 in their IR database. I asked for, but have not received, the IR codes for the TX-NR515 which MAY work.

Perhaps there's an equivalent Integra unit and those codes would work?
Post 4 made on Friday April 27, 2012 at 10:30
MacrossZero
Active Member
Joined:
Posts:
March 2009
594
I am sorry that I did not understand your problem.  Here is the page link on Remote Central for the Hex codes for Onkyo.
[Link: files.remotecentral.com]

This is what I have in my database.

Power Off

0000 006C 0022 0002 0156 00AC 0016 0016 0016 0040 0016 0016 0016 0016 0016 0040 0016 0016 0016 0040 0016 0040 0016 0016 0016 0016 0016 0040 0016 0040 0016 0016 0016 0040 0016 0040 0016 0016 0016 0040 0016 0040 0016 0040 0016 0016 0016 0016 0016 0016 0016 0040 0016 0016 0016 0016 0016 0016 0016 0016 0016 0040 0016 0040 0016 0040 0016 0016 0016 0040 0016 05CC 0156 0055 0016 0E5D

Power On

0000 006C 0022 0002 0156 00AC 0016 0016 0016 0040 0016 0016 0016 0016 0016 0040 0016 0016 0016 0040 0016 0040 0016 0040 0016 0016 0016 0040 0016 0040 0016 0016 0016 0040 0016 0040 0016 0016 0016 0016 0016 0016 0016 0040 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0040 0016 0040 0016 0016 0016 0040 0016 0040 0016 0040 0016 0040 0016 0040 0016 05CC 0156 0055 0016 0E5D
Do or Do not, There is no Try.
OP | Post 5 made on Friday April 27, 2012 at 17:26
Trunk-Slammer -Supreme
Loyal Member
Joined:
Posts:
November 2003
7,402
Thanks,

I'll give those a try.


I got another reply from Onkyo on their support forums. Pretty sure they're just BS'ing....

Hopefully I can get this thing to respond to something before I have to replace it with something else and eat the cost....
Post 6 made on Saturday December 22, 2012 at 01:40
Ouest Domotique
Lurking Member
Joined:
Posts:
December 2012
1
Hello,

Did it work for you?
I am also looking for a discret Power ON and OFF for the same Receiver?

Regards,
JP
Post 7 made on Saturday December 22, 2012 at 09:46
Hasbeen
Loyal Member
Joined:
Posts:
November 2007
5,271
Try the Integra Codes.  They'll typically work.
Post 8 made on Saturday December 22, 2012 at 14:20
Avparts.com
Long Time Member
Joined:
Posts:
May 2009
215
Onkyo TXNR515 and higher ( I have NOT tried these yet on TXNR414 though)

Remote ID1
Power On
0000 006D 0022 0002 0156 00AB 0015 0015 0015 003F 0015 0015 0015 0015 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 0015 0015 003F 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 003F 0015 003F 0015 05CC 0156 0055 0015 0E47

Power Off
0000 006D 0022 0002 0156 00AB 0015 0015 0015 003F 0015 0015 0015 0015 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 0015 0015 0015 0015 003F 0015 0015 0015 0015 0015 0015 0015 0015 0015 003F 0015 003F 0015 003F 0015 0015 0015 003F 0015 05F6 0156 0055 0015 0E47
Wil Vitela, owner
Why can't more manufacturers listen to custom installers?
Post 9 made on Sunday December 23, 2012 at 09:21
Ziontao
Long Time Member
Joined:
Posts:
May 2006
26
The new Onkyo NR Series has a random issue with some of the models power commands not working with universal remotes.  Onkyo has fixed most of these problems with the latest firmware updates.

I suggest you update the firmware (may take more than one to get up to speed), then re-check the discrete power commands again.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse