Hello,
MYTEK Brooklyn DAC supports the following RC5 odes:
Rc5Command_Standby = 12, Rc5Command_Mute = 13, Rc5Command_Menu = 82, Rc5Command_VolUp = 16, Rc5Command_VolDown = 17, Rc5Command_ProgramUp = 32, Rc5Command_ProgramDown = 33, Rc5Command_ActuatorUp = 80, Rc5Command_ActuatorDown = 81,
According to manual, the device should automatically find the remote address of the remote: 4. Press any button on the RC5 compatible remote. The Brooklyn DAC find the address automatically 5. Done! - the remote is paired
I'm using irplus application on my smartphone and it actually works, when I press the button, the device finds automatically the remote addrress.
I have found so far the following hex codes that are working:
// remote addr 5 STANDBY 0000 0073 0000 000A 0020 0020 0040 0020 0020 0020 0020 0040 0040 0040 0040 0020 0020 0040 0020 0020 0040 0020 0020 0CC8 PROGRAM+ 0000 0073 0000 000B 0020 0020 0040 0020 0020 0020 0020 0040 0040 0040 0020 0020 0040 0020 0020 0020 0020 0020 0020 0020 0020 0CC8 PROGRAM-0000 0073 0000 000B 0020 0020 0040 0020 0020 0020 0020 0040 0040 0040 0020 0020 0040 0020 0020 0020 0020 0020 0020 0040 0020 0CA8
// remote addr 17 STANDBY 0000 0073 0000 000A 0020 0020 0040 0040 0040 0020 0020 0020 0020 0040 0040 0020 0020 0040 0020 0020 0040 0020 0020 0CC8
// remote addr 16 VOLUME+ 0000 0073 0000 000B 0020 0020 0040 0040 0040 0020 0020 0020 0020 0020 0020 0020 0020 0040 0040 0020 0020 0020 0020 0020 0020 0CC8 VOLUME- 0000 0073 0000 000B 0020 0020 0040 0040 0040 0020 0020 0020 0020 0020 0020 0020 0020 0040 0040 0020 0020 0020 0020 0040 0020 0CA8
// remote addr 20 PROGRAM+ 0000 0073 0000 000A 0020 0020 0040 0040 0040 0040 0040 0020 0020 0040 0040 0020 0020 0020 0020 0020 0020 0020 0020 0CC8 PROGRAM- 0000 0073 0000 000A 0020 0020 0040 0040 0040 0040 0040 0020 0020 0040 0040 0020 0020 0020 0020 0020 0020 0040 0020 0CA8
However, I am facing two issues:
1/ When device is turned off, when I press STANDBY button, the device turns on nicely. Unfortunately, when I push the STANDBY button to turn off the device, it does not react. I'm able to turn off the device only when I hit the STANDBY button very very fast. Sometimes it reacts after 2, sometimes after 5 very quick button presses.
For me looks like some problem with the timing of the remote / codes. Is it possible to somehow tweak it? What should I change in HEX code of STANDBY buttons?
The same situation happens when I press STANDBY button after programing the DAC for remote addr 5 and 17.
2/ What are the other supported IR codes for given Remote Addr ? If I have below codes for Remote Addr 5: // remote addr 5 STANDBY PROGRAM+ PROGRAM-
Can you help with getting hex codes for other supported functions like MUTE, MENU, VOLUME+, VOLUME-, ACTUATOR+, ACTUATOR- ?
Thanks in advance and Best Regards, Przemek
|