Your Universal Remote Control Center
RemoteCentral.com
Discrete Code Hunter Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
Panasonic PT-AX200U Projector Discrete On/Off?
This thread has 6 replies. Displaying all posts.
Post 1 made on Thursday March 27, 2008 at 20:21
KrisRoberts
Long Time Member
Joined:
Posts:
March 2008
19
I know its a long shot, but my LCD projector is the only device in my setup that toggles its power. Does anyone have discrete power codes for the PT-AX200U ?
Post 2 made on Thursday March 27, 2008 at 21:03
Rob100
Long Time Member
Joined:
Posts:
July 2007
79
Try these. I don't have a AX200 so can't test, but think these should work.

Power On

0000 0070 0000 003A 0081 0041 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0030 000F 0030 000F 0030 000F 0030 000F 0030 000F 000F 000F 000F 000F 000F 000F 0030 000F 0030 000F 000F 000F 0030 000F 0030 000F 0030 000F 0030 000F 0ABD

Power Off

0000 0070 0000 003A 0080 0041 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 0030 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 000F 0030 000F 0030 000F 0030 000F 0030 000F 0030 000F 0030 000F 000F 000F 000F 000F 0030 000F 0030 000F 0030 000F 000F 000F 0030 000F 0030 000F 0030 000F 0030 000F 0ABD
OP | Post 3 made on Friday March 28, 2008 at 12:46
KrisRoberts
Long Time Member
Joined:
Posts:
March 2008
19
These work great with my PT-AX200U and Pronto.

Thank you so much!

Last edited by KrisRoberts on March 29, 2008 00:02.
Post 4 made on Thursday April 3, 2008 at 15:41
moreflan
Lurking Member
Joined:
Posts:
April 2008
1
I had the same problem, and since I don't have a pronto, I had to come up with a substitute. It isn't as neat obviously, but thus far, it's doing its job as part of a set of macros for a mx-900.

on = power, return
off = power, power

If projector is off, the "power" command turns the projector on, and the "return" does nothing. If projector is already on (for example, switching from dvd viewing to cable box viewing ), the first "power" will bring up the confirmation screen. The "return" will simply cancel the command. Again, it's not the prettiest solution, but it let's me switch activities without worrying about accidentally switching off the projector and waiting 5 minutes for it to come back on.

There may be one other drawback. I haven't tested this, but if the projector is off, running the "off" macro will probably turn the projector on.
Post 5 made on Thursday April 3, 2008 at 15:45
Kupakai
Long Time Member
Joined:
Posts:
September 2006
230
On April 3, 2008 at 15:41, moreflan said...
I had the same problem, and since I don't have a pronto,
I had to come up with a substitute. It isn't as neat
obviously, but thus far, it's doing its job as part of
a set of macros for a mx-900.

Can't you import the Pronto hex code above using universal browser in your software?
Post 6 made on Thursday April 3, 2008 at 16:38
Rob100
Long Time Member
Joined:
Posts:
July 2007
79
On April 3, 2008 at 15:45, Kupakai said...
Can't you import the Pronto hex code above using universal
browser in your software?

I wondered that myself, but just downloaded the programming manual for that remote and it appears you can import a ccf, but not enter to codes directly!? If this is the case then I (or someone else) could easily create a ccf with those commands in for you to import.
Post 7 made on Thursday April 3, 2008 at 17:44
Rob100
Long Time Member
Joined:
Posts:
July 2007
79
On April 3, 2008 at 16:38, Rob100 said...
I wondered that myself, but just downloaded the programming
manual for that remote and it appears you can import a
ccf, but not enter to codes directly!? If this is the
case then I (or someone else) could easily create a ccf
with those commands in for you to import.

I've just questioned this with "ekroner" from this forum (as he knows about these things) and he tells me that:

"you can go from pronto hex into the URC software. The manual you have might be outdated because they do have that functionality now (they didn't always)."

So maybe you just need to download newer software?


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse