|
|
|
Discrete Code Hunter Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
descrete codes for mitsubishi wd-52628
| |
|
Topic: | descrete codes for mitsubishi wd-52628 This thread has 6 replies. Displaying all posts. |
|
Post 1 made on Friday June 23, 2006 at 21:40 |
i was wonering if any one had the descrete codes for this tv
|
|
Post 2 made on Friday July 21, 2006 at 13:54 |
I have the discrete codes for this model. If you have a fax number I can send them to you.
|
|
Post 3 made on Monday August 7, 2006 at 22:12 |
tredn Lurking Member |
Joined: Posts: | August 2006 2 |
|
|
On July 21, 2006 at 13:54, ccsprog said...
I have the discrete codes for this model. If you have a fax number I can send them to you.
|
|
Post 4 made on Monday August 7, 2006 at 22:14 |
tredn Lurking Member |
Joined: Posts: | August 2006 2 |
|
|
ccsprog can you send me those discrete codes too?
|
|
Post 5 made on Wednesday September 13, 2006 at 14:52 |
mnovak16 Long Time Member |
Joined: Posts: | September 2006 12 |
|
|
ccsprog, would you mind sending the codes for that tv to me as well. I would greatly appreciate it. [email protected] Thanks.
|
|
Post 6 made on Sunday September 24, 2006 at 19:27 |
jw11301a Lurking Member |
Joined: Posts: | January 2005 9 |
|
|
Does this Mits model have HDMI inputs? If so, do you think they would work for the WD-75731?
|
John W. |
|
Post 7 made on Monday October 16, 2006 at 22:30 |
Gerald Koth Founding Member |
Joined: Posts: | August 2001 198 |
|
|
Here are codes for the newer Mitsu models
Applicable Remote Controls and Televisions This document applies to the full size television remote controls introduced in 2006. The inputs specified below apply to the TVs that included these remotes. If a model does not have the specified input, or there is no connection to the specified input, the TV will not respond to the direct access signal. The 731 series TVs have a PC DVI-I input, however these models do not respond to the PC DVI-I access signal.
Procedure to program the remote for special direct access functions:
Set the Device Select Switch at the top to the TV position. Press and hold the POWER key until it flashes twice, then release the POWER key. Enter in sequence the code number 0,0,0,9,0. The POWER key will flash twice after the first 0 and then flash twice again after the final 0 to confirm a successful code entry.
The following keys will change functions: POWER - Power ON only. STOP - Power OFF only. PAUSE - AV RESET (resets audio and video adjustments).
INPUT followed by 1 - INPUT-1 INPUT followed by 2 - INPUT-2 INPUT followed by 3 - INPUT-3 INPUT followed by 4 - HDMI 2 INPUT followed by 5 - COMPONENT-1 INPUT followed by 6 - COMPONENT-2 INPUT followed by 7 - COMPONENT-3 INPUT followed by 8 - ANT 2 INPUT followed by 9 - ANT 1 INPUT followed by F1 - HDMI 1 INPUT followed by F3 - PC DVI-I Input (not available for 731 series)
FORMAT followed by 1 - STANDARD screen format FORMAT followed by 2 - EXPAND screen format FORMAT followed by 3 - ZOOM screen format FORMAT followed by 4 - STRETCH screen format FORMAT followed by 5 - STRETCH PLUS screen format FORMAT followed by 6 - NARROW screen format FORMAT followed by 7 - WIDE EXPAND screen format
IMPORTANT: When using this remote control as an original source remote control to program a "learning" remote control or Home Automation control system, the INPUT and FORMAT keys do not send signals. These buttons are simply used as a "switch" function to prepare the remote control to send the correct input or format signal when the number key or other specified key is pressed.
IMPORTANT: This remote control was included with TVs that had Auto Input Sensing. Direct access to inputs that have not been connected and added to the active input list is not possible.
Procedure to return the remote control to normal consumer functions:
Set the Device Select Switch at the top to the TV position. Press and hold the POWER key until it flashes twice, then release the POWER key. Enter in sequence the code number 0,0,9,3,5. The POWER key will flash twice after the first 0 and then flash twice again after the final 5 to confirm a successful code entry.
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|