|
|
|
Custom Installers' Lounge Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
cutting an outlet in stone
| |
|
Topic: | cutting an outlet in stone This thread has 19 replies. Displaying posts 1 through 15. |
|
Post 1 made on Monday July 17, 2006 at 18:41 |
Curious how to go about this. I need to install an outlet in a stone fireplace for an LCD mount... I don’t think its real stone, rather synthetic if it makes any difference. I'm not sure what to use to get a nice cut for the box. Any help is appreciated.
|
|
Post 2 made on Monday July 17, 2006 at 18:44 |
tschulte Advanced Member |
Joined: Posts: | November 2005 808 |
|
|
You will need a good hammerdrill (perferably a corded one). A 1/4" masonary bit. A 4" angle grinder and some cold chisels. A face mask and a vacuum would also be good.
I am just curious, how will you get the wire to it?
|
Just my opinion, I could be wrong. |
|
Post 3 made on Monday July 17, 2006 at 18:54 |
tweetymp4 Select Member |
Joined: Posts: | March 2003 2,140 |
|
|
how do you get the wires to it?
What is behind the stone?
|
I'm Not an engineer, but I play one on TV. My handle is Tweety but I have nothing to do with the organization of similar name. I just had a really big head as a child so folks called me tweety bird. |
|
OP | Post 4 made on Monday July 17, 2006 at 18:56 |
Theres drywall on both sides, Im ging to put inwall speakers on either side which will give me access to pull the wires......i hope. I'm pretty sure it hollow behind it. Do I drill first then use the grinder to square it up?
|
|
Post 5 made on Monday July 17, 2006 at 19:01 |
low profile surface mount box
|
McPancakes, its whats for breakfast! |
|
OP | Post 6 made on Monday July 17, 2006 at 19:05 |
can you give me a manufacturer or are the as common as reg boxes? Thats a good idea.
|
|
Post 7 made on Tuesday July 18, 2006 at 03:12 |
Ernie Bornn-Gilman Yes, That Ernie! |
Joined: Posts: | December 2001 30,104 |
|
|
How old is this? I mean, if it were in California (your profile doesn't say where you are, which would allow suggestions from people in your region) and maybe as much as ten years old, you could count on it being a double metal tube with air space around it. Fifty years old, it's probably solid brick behind the stone. In between. anybody?
And how do you get the signal to it?
|
A good answer is easier with a clear question giving the make and model of everything. "The biggest problem in communication is the illusion that it has taken place." -- G. “Bernie” Shaw |
|
Post 8 made on Tuesday July 18, 2006 at 03:50 |
elnickster Long Time Member |
Joined: Posts: | June 2004 227 |
|
|
Theres drywall on both sides, Im ging to put inwall speakers on either side which will give me access to pull the wires......i hope. I'm pretty sure it hollow behind it. Do I drill first then use the grinder to square it up? I hate to be the a$$hole here, but if you have to ask, you don't know what you're doing. Where in the country are you?
|
Nickster |
|
OP | Post 9 made on Tuesday July 18, 2006 at 07:14 |
I’m in Kennett sq Pa. Sorry I didn't have that in there. I work for a co. that specializes in custom home theater systems, mostly projection sys. this is the first time someone has asked me to put an lcd over a fire place. It’s a brand new house. The fireplace is on an exterior wall, huge cathedral ceiling,(stone goes from floor to ceiling). The gas is vented very low, which leads me to believe (and I talked to some people who install the fireplaces) that the portion behind where the TV is going to be mounted is an empty cavity. There is a bump out for the vent on the outside wall and for esthetics they continue the bump out all the way up to the 2nd story. There’s no vents etc... out the top. I'm only running an outlet and or HDMI or Component cables to the back of the TV along with electric. The receiver controls everything else. Just thought someone could tell me how to cut a nice outlet box. I'm not completely out of my realm here, just wanted some input.
|
|
Post 10 made on Tuesday July 18, 2006 at 07:57 |
djnorm Founding Member |
Joined: Posts: | January 2002 1,693 |
|
|
If the outside of the chimney is vinyl siding, it's a good bet it's not solid brick. Also a good bet there are studs behind the stone to mount to too.
|
|
Post 11 made on Tuesday July 18, 2006 at 08:51 |
Ted Wetzel Founding Member |
Joined: Posts: | November 2001 879 |
|
|
personally I have the stone guys come back and cut the hole. That way if it gets screwed up they are right there to fix it. They can get that hole in there in half the time it will take you.
|
|
Post 12 made on Tuesday July 18, 2006 at 10:13 |
FreddyFreeloader Super Member |
Joined: Posts: | April 2004 3,243 |
|
|
1) How to tell if it is hollow- drill 1/4 inch hole near where your speakers will be cut out. Then use your fish rods to poke around.
2) Push the rods toward the back of the mount and see how free your wires will be behind the synthetic looking brick.
3)Think good thoughts.
|
|
Post 13 made on Tuesday July 18, 2006 at 10:14 |
brandenpro Select Member |
Joined: Posts: | May 2005 1,651 |
|
|
cut the drywall holes first for the speakers. That way if its not hollow you dont have a nice hole in the stone.
|
|
Post 14 made on Tuesday July 18, 2006 at 14:15 |
ceied Loyal Member |
Joined: Posts: | February 2002 5,754 |
|
|
hire a pro....
|
Ed will be known as the Tiger Woods of the integration business, followed closely with the renaming of his company to "Hotties A/V". The tag line will be "We like big racks and tight holes"... |
|
Post 15 made on Tuesday July 18, 2006 at 14:55 |
Theaterworks Founding Member |
Joined: Posts: | April 2002 1,898 |
|
|
See below, double post.
|
Carpe diem! |
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|