Your Universal Remote Control Center
RemoteCentral.com
Custom Installers' Lounge Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
IR Distribution
This thread has 5 replies. Displaying all posts.
Post 1 made on Tuesday December 17, 2002 at 22:11
Brian Bowman
Long Time Member
Joined:
Posts:
November 2002
10
I have a question with regards to a specific component I'm not terribly familiar with - and I'm hoping someone here can share the answer. Yamaha components offer a "remote in/out" feature (via mini-plug on the back panel), allowing them to receive IR remote signals via hardwire. I am installing an RX-V1 receiver into a cabinet with a solid front door (don't worry, the back is open... plenty of ventilation) and am going to be adding an IR sensor outside the cabinet. Now - my question... can I run the output of that sensor directly into the "remote in" jack of the Yamaha? Should/could I run the sensor first into a powered distribution block and then into the "remote in"? Or will this not work - and I should just tack an emitter over the existing IR eye on the front of the RX-V1? Thanks!

-Brian
Post 2 made on Tuesday December 17, 2002 at 22:19
quest51459
Founding Member
Joined:
Posts:
September 2001
197
Brian,
What kind of amplified block are you using? If it's xantech you just use a mono mini plug out of the emitter port of the block to the in on the yamaha. If you have any problems email me at [email protected]. I'm a high home theater designer in ny and the yahama advisory board.
Post 3 made on Tuesday December 17, 2002 at 23:09
swfla.rr.com
Long Time Member
Joined:
Posts:
July 2002
103
You should be able to run through an amplified block, however on very few occasions an amplified block may produce an output signal that is too "hot". If this should occur (verify by sending sensor signal directly to ir in) the solution would be to use a non-amplified block. I think the answer to your question is simple, any Xantech compatible signal is capable of being manipulated with connecting blocks. I personally can't stand emitters stuck on any piece of equipment. It always seems to be a cleaning persons easy target. If IR distribution is a subject of interest then try to locate a resource published by Xantech called "The Book". I believe it is no longer available, but there are millions out there soaking coffee off installation van floors. GOOD LUCK
Post 4 made on Wednesday December 18, 2002 at 12:30
Theaterworks
Founding Member
Joined:
Posts:
April 2002
1,898
I believe it is no longer available

Really? That would be a mistake on Xantech's part; how else are we to work out which of their zillion black boxes we need for a job? Do they publish a .pdf or something? And what will I use for a coffee coaster from now on?
Carpe diem!
Post 5 made on Wednesday December 18, 2002 at 12:50
twix
Long Time Member
Joined:
Posts:
July 2002
109
On 12/17/02 22:19.18, quest51459 said...
. I'm a high home theater designer
in ny and the yahama advisory board.

Like wow man, that's far out!
OP | Post 6 made on Wednesday December 18, 2002 at 23:54
Brian Bowman
Long Time Member
Joined:
Posts:
November 2002
10
Thanks guys,

Yes, it is a Xantech system that I'll be using - so I'll try coming straight out of the connecting block into the back of the receiver. Hopefully it'll work just fine. Thanks for the info!

-Brian Bowman


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse