|
|
|
The following page was printed from RemoteCentral.com:
using 1 remote with 3 identical receivers
| |
|
Topic: | using 1 remote with 3 identical receivers This thread has 11 replies. Displaying all posts. |
|
Post 1 made on Wednesday May 24, 2006 at 13:49 |
jsapiente Lurking Member |
Joined: Posts: | December 2002 4 |
|
|
I am designing an entertainment unit that has 3 tv's. I will be using the same HD direct tv receivers and would like to know how I can pick a remote that will allow me to control all components on as needed basis. If I want to change tv one how do I do that and not change tv's 2 and 3
|
|
Post 2 made on Wednesday May 24, 2006 at 14:13 |
fibercut Long Time Member |
Joined: Posts: | February 2003 12 |
|
|
Crestron
|
We sell the un-necessary to the un-greatful... ;o) |
|
Post 3 made on Wednesday May 24, 2006 at 14:35 |
SoundExp Long Time Member |
Joined: Posts: | December 2004 47 |
|
|
We do a few of these systems a year. Use RTI. We use the T1 remote with an RP6 and RM433 RF unit. The RP6 has 6 assignable ports. Works perfect every time.
|
|
Post 4 made on Wednesday May 24, 2006 at 14:36 |
Fred Harding Super Member |
Joined: Posts: | October 2001 3,460 |
|
|
Xantech rt8 or universal remote with mrf250 or mrf300
|
On the West Coast of Wisconsin |
|
Post 5 made on Wednesday May 24, 2006 at 14:40 |
AnthonyZ Select Member |
Joined: Posts: | September 2005 1,987 |
|
|
I second the URC w/ mrf300. Niles also has "addressable" IR if RF is an issue (especially where DVR's are used, lot's of interference). It seems that virtually every job we do lately is multiple display. I don't know how client's do it. It drives me insane to have more than one thing to concentrate on at any given time.
|
"Just when I thought that I was out they pull me back in" |
|
Post 6 made on Wednesday May 24, 2006 at 14:54 |
Fred Forlano Long Time Member |
Joined: Posts: | June 2002 433 |
|
|
When you use IR routing, whether it's Xantech, URC, RTI, Crestron/AMX, etc. (all of which are good solutions depending on budget), make sure you take into consideration WHERE your equipment is going to live. It can still be affected by stray IR if, for example, the DSS receivers are all stacked on top of one another. Use the rubber IR emitter covers (Xantech, Niles, etc.) for nice clean appearance, or black tape (Scotch Super 33m, Duck, etc.) for not-so-nice appearance.
Just a thought.
Fred Forlano Higher Definition
|
"I have been marked once, my dear and let me assure you, no needle shall ever touch my skin again." -- Erik Magnus Lensherr (Magneto) |
|
Post 7 made on Wednesday May 24, 2006 at 14:58 |
Sc0tty Active Member |
Joined: Posts: | July 2003 594 |
|
|
Yep... RF routing has to be done... The MX stuff works well when you can get around the RF problems, but just go straight to the MRF-300 and this will elimainated 95% of RF issues with the MX products...You have to be slick in the setup, and of course you customer will have to have some savvy, but it is easily done. I did the same deal with a office housing a 60" Pioneer Elite plasma, and (2) 37" Sharp Aquos LCD. Worked great..
|
I long for a better world. One in which a chickens motives will not be questioned when mearly crossing the road. |
|
Post 8 made on Thursday May 25, 2006 at 06:38 |
Springs Super Member |
Joined: Posts: | May 2002 3,238 |
|
|
RTI T3/RP6/RM433 + some IR flashers onm seperate ports. Only the Macros will make you go in and do them over one at a time.
|
|
Post 9 made on Thursday May 25, 2006 at 07:23 |
I always prefer to use the TV's serial port for control where possible (can't always be done due to budget restrictions).
It gives true feedback to the processor (if you're using one), and each TV is totally isolated from all of the other TV's.
|
|
Post 10 made on Thursday May 25, 2006 at 09:13 |
DIRTE Active Member |
Joined: Posts: | February 2005 500 |
|
|
On May 24, 2006 at 14:36, Fred Harding said...
Xantech rt8 or universal remote with mrf250 or mrf300 I didnt think you could address the line outs on the mrf-250? I had the same situation where I needed to control four identical TV's and used a mx3000 with a mrf-300 controlling all the gear RF. All you have to do is assign the emitters going to the gear to the appropriate device on the remote. Good Luck
|
"Twenty years from now, you will be more disappointed with the things you didn't do than by the things you did… Explore. Dream. Discover" Mark Twain, 1879 |
|
Post 11 made on Thursday May 25, 2006 at 09:38 |
Fred Harding Super Member |
Joined: Posts: | October 2001 3,460 |
|
|
On May 25, 2006 at 09:13, DIRTE said...
I didnt think you could address the line outs on the mrf-250?
According to their web site, mrf250 offers ir routing as well.
|
On the West Coast of Wisconsin |
|
Post 12 made on Thursday May 25, 2006 at 12:23 |
Jeff Wagner Founding Member |
Joined: Posts: | January 2002 368 |
|
|
Yes, the MRF250 allows for IR routing. If the boxes you are using have hard drives (DVR type) then you may wish to use the MRF300 as it allows you to move the antenna away from sources of RF interference (DVR's).
Jeff
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|