|
|
|
Custom Installers' Lounge Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
Xantech IRS232A with InFocus LP-820
| |
|
Topic: | Xantech IRS232A with InFocus LP-820 This thread has 9 replies. Displaying all posts. |
|
Post 1 made on Tuesday November 29, 2005 at 20:32 |
Michael Clarke Long Time Member |
Joined: Posts: | September 2003 169 |
|
|
I have a situation where I need to have discrete control over an InFocus LP-820 projector in a boardroom. The LP-820 doesn't have discrete IR for ON/OFF so I'm planning to use a Xantech IR to RS-232 converter. Has anyone tried this combination & with what results?
|
Ever notice when you are driving that everybody going slower than you is an idiot and everyone going faster than you is a maniac. |
|
Post 2 made on Tuesday November 29, 2005 at 21:45 |
TouchCommander Active Member |
Joined: Posts: | December 2004 602 |
|
|
Have used many times with NEC, Infocus, and others. Note that you still have to wait for cool down period before turning back on.
|
No job to small, many to big |
|
Post 3 made on Tuesday November 29, 2005 at 23:21 |
vwpower44 Super Member |
Joined: Posts: | August 2004 3,662 |
|
|
I believe the Infocus stuff has a 20 second IR Lockout, so put in a long delay, but controlling it via RS232 should not be a problem.
Mike
|
Stay Hungry, Stay Foolish... |
|
OP | Post 4 made on Wednesday November 30, 2005 at 06:12 |
Michael Clarke Long Time Member |
Joined: Posts: | September 2003 169 |
|
|
Thanks for the replies.
TouchCommander, I understand about not being able to turn on during cool down period. I don't have a problem with that.
vmpower44, please expand on 20 second IR lockout & long delay.
Regards
|
Ever notice when you are driving that everybody going slower than you is an idiot and everyone going faster than you is a maniac. |
|
Post 5 made on Wednesday November 30, 2005 at 12:28 |
vwpower44 Super Member |
Joined: Posts: | August 2004 3,662 |
|
|
When you first turn on the project, they have a 20 second period in which you cannot send an IR command to the unit. I don't know if that applies to any RS232 commands. If so, you will have to add a 20 second delay after the Power on command.
Mike
|
Stay Hungry, Stay Foolish... |
|
OP | Post 6 made on Thursday January 12, 2006 at 22:02 |
Michael Clarke Long Time Member |
Joined: Posts: | September 2003 169 |
|
|
I finished the install with the Infocus LP-820 and the Xantech IRS232A. Everything works great. I now have discrete control over all the electronics on this project. Using a Pronto TSU-7500 and RFX-6500.
|
Ever notice when you are driving that everybody going slower than you is an idiot and everyone going faster than you is a maniac. |
|
Post 7 made on Tuesday February 7, 2006 at 19:49 |
tbilliet Lurking Member |
Joined: Posts: | November 2005 1 |
|
|
Question:
I am attempting a very similar scenario. . . Using a Xantech IRS232A to control a Proxima C460 via RS232.
The room is controlled with a Marantz 9500 & RX-77 RF Extender.
1st problem, the projector does not respond to the Xantech at all. ( I have confirmed that the correct ASCII strings are being sent & have tried the "test" feature in the Dragon Drop software)
2nd problem, the RX-77 does not seem to be talking to the IRS232A. The RX-77 is receiving the signal from the remote (LED lights indicate this), but then there is no response from the IRS232A (LED's show no activity)
Any ideas and/or suggestions would be greatly appreciated.
Thanks!!!
|
|
Post 8 made on Wednesday February 8, 2006 at 02:02 |
BCM-OZ Active Member |
Joined: Posts: | April 2004 534 |
|
|
RX-77 / LI-900 are a known PITA to integrate with Xantech. Search this forum for many previous posts regarding this.
|
|
OP | Post 9 made on Friday February 10, 2006 at 15:18 |
Michael Clarke Long Time Member |
Joined: Posts: | September 2003 169 |
|
|
tbilliet,
When you use the "test" feature in Dragon Drop, does the projector respond?
|
Ever notice when you are driving that everybody going slower than you is an idiot and everyone going faster than you is a maniac. |
|
OP | Post 10 made on Friday February 10, 2006 at 15:47 |
Michael Clarke Long Time Member |
Joined: Posts: | September 2003 169 |
|
|
tbilliet,
Did you program the IRS232a to the following settings to communicate with the Proxima ?
Bits per second: 19,200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None
Are you using a null modem cable between the Xantech irs232a and the proxima?
Command Format: All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses.
|
Ever notice when you are driving that everybody going slower than you is an idiot and everyone going faster than you is a maniac. |
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|