 |
 |
|
|
Custom Installers' Lounge Forum - View Post
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
| Topic: | Question for AMX Experts This thread has 7 replies. Displaying all posts. |
|
| Post 1 made on Saturday January 29, 2005 at 05:56 |
QQQ Super Member |
Joined:
Posts: | January 2002
4,806 |
|
|
What are the capabilities of current Netlinx controllers as far as replacing an old PHAST Landmark card frame and:
Integrating with other Landmark components such as the Landmark audio switcher, DMS keypads and also the now defunct Landmark/PHAST light switches. I believe the first two are no problem? but I do not know about the lighting.
|
|
| OP | Post 2 made on Saturday January 29, 2005 at 06:12 |
QQQ Super Member |
Joined:
Posts: | January 2002
4,806 |
|
|
I would also like to know what the part number is of what I assume is some type of Netlinx to Landmark (Echelon) converter that allows Netlinx to talk to Landmark components.
|
|
| Post 3 made on Saturday January 29, 2005 at 13:32 |
Impaqt RC Moderator |
Joined:
Posts: | October 2002
6,233 |
|
|
Whoa... Could of SWORN I responded to this already... Weird...
Anyway.. All Cuurent NI Series Processor support ICSNet, which is the new name for PHASTLink. Keypads, and Audio switcher plug right in and AMX has pre-written modules to runthem. Probobly will need to update the Firmware on the PHAST Devices.. But I think its all Software upload...
Just get the Processor that will accomodate all the source componets you need to control.... Let me know if you need any help witht he right specs....
|
|
|
| OP | Post 4 made on Saturday January 29, 2005 at 13:42 |
QQQ Super Member |
Joined:
Posts: | January 2002
4,806 |
|
|
Impaqt,
The big question is can the old PHAST lighting stuff be supported?
|
|
| Post 5 made on Saturday January 29, 2005 at 15:07 |
Robert Parker Senior Member |
Joined:
Posts: | March 2004
1,488 |
|
|
QQQ,
The web site has modules for the PLK-MLC and PLK-MWD. There are modules for all Phast audio components. Think of them as drivers. You compile them with the code. In most cases you talk to the driver and not the device itself. We never did Phast lighting, aways Lutron, so I can't speak to that. I have found that all AS8/16s, AMP8s, 2 button, and MSP8s will work with their current firmware. I had problems with DMSs earlyer than 5.0 or 5.01. I think the current is 5.16. To upgrade firmware you must replace a chip in side the DMS. The last job I did I updated 13. 12 worked and 1 had to be replaced.
Robert
|
Clatto Verata... Necktie |
|
| Post 6 made on Saturday January 29, 2005 at 15:25 |
Impaqt RC Moderator |
Joined:
Posts: | October 2002
6,233 |
|
|
PLl-PWD/PLL-MLC Phastlink PWD/MLC
FG2601 PWD-MLCMod.tko (Netlinx Module)
***************************************************************************
***************************************************************************
Note: As of NetLinx master build c2.10.76, this module is no longer needed.
The NetLinx master has built in support for this device.
***************************************************************************
***************************************************************************
---------------------------------------------------------------------------
Netlinx Module Revision History
Date Version Firmware Name
---------------------------------------------------------------------------
06/28/01 v1.01 Changed manufacturer name
---------------------------------------------------------------------------
01/11/00 v1.00 Added Preset Commands
Added Preset Parameter to Module Line
---------------------------------------------------------------------------
11/15/00 v0.91 Added VERSION command
---------------------------------------------------------------------------
10/12/00 v0.90 Initial Production Release
---------------------------------------------------------------------------
Minimum Version:
Netlinx Studio Build 101
Netlinx Master Build 65
Note: As of NetLinx master build c2.10.76, this module is no longer needed.
The NetLinx master has built in support for this device.
Looks like you dont need the module anymore for the old lightswitches/Dimmers.....
DOnt see many PHAST Lightign systems working still..... (Hell.. didnt see that many working when they were new..... ;)
|
|
|
| OP | Post 7 made on Saturday January 29, 2005 at 16:50 |
QQQ Super Member |
Joined:
Posts: | January 2002
4,806 |
|
|
DOnt see many PHAST Lightign systems working
still.....
(Hell.. didnt see that many working when they
were new..... ;) Neither did I $%$!#!! ;-).
|
|
| OP | Post 8 made on Saturday January 29, 2005 at 16:50 |
QQQ Super Member |
Joined:
Posts: | January 2002
4,806 |
|
|
Thanks for the answers Impaqt and Robert.
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
