|
|
|
Custom Installers' Lounge Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
MX-3000 systems interfering
| |
|
Topic: | MX-3000 systems interfering This thread has 11 replies. Displaying all posts. |
|
Post 1 made on Wednesday December 22, 2004 at 21:07 |
Kris411 Lurking Member |
Joined: Posts: | December 2004 9 |
|
|
I was having a problem with two different mx-3000's interfering. When changing channels on the dish in the master, the living room will change also. This only happens when using both remotes at the same time, both on dish. I do have different RF settings on each. The systems don't interfere, unless using both remotes at once. Any ideas???
|
|
Post 2 made on Wednesday December 22, 2004 at 21:10 |
oex Super Member |
Joined: Posts: | April 2004 4,177 |
|
|
what channel(s) is the mxf250 set on?
Is the equipment in a rack all together?
|
Diplomacy is the art of saying hire a pro without actually saying hire a pro |
|
OP | Post 3 made on Wednesday December 22, 2004 at 21:14 |
Kris411 Lurking Member |
Joined: Posts: | December 2004 9 |
|
|
I forget the exact, but I believe it was 3, and e. We are going back toimorrow. They are in separate rooms, about 20 feet apart. one sits behind a cabinet in the master, and the other is in the family room rack.
|
|
Post 4 made on Wednesday December 22, 2004 at 21:16 |
oex Super Member |
Joined: Posts: | April 2004 4,177 |
|
|
is both units sending RF only to the mxf receivers?
And only sending signal to the one flasher connected to the sat box?
|
Diplomacy is the art of saying hire a pro without actually saying hire a pro |
|
OP | Post 5 made on Wednesday December 22, 2004 at 21:19 |
Kris411 Lurking Member |
Joined: Posts: | December 2004 9 |
|
|
They are totally seperate systems. 2 different sat boxes, in 2 different rooms, with 2 different 250's. We found it happening when testing macros for the camera system in one room and it would lockout the living room remote, and be controlled byt the master remote, and vise-versa
|
|
Post 6 made on Wednesday December 22, 2004 at 21:21 |
oex Super Member |
Joined: Posts: | April 2004 4,177 |
|
|
Hmmmmm.
Id try removing the antenna but doubt that would help since they are so close.
Im give it some more thought
|
Diplomacy is the art of saying hire a pro without actually saying hire a pro |
|
OP | Post 7 made on Wednesday December 22, 2004 at 21:25 |
Kris411 Lurking Member |
Joined: Posts: | December 2004 9 |
|
|
We already removed them. I appreciate the help. Let me know if you have any other ideas we could try.
|
|
Post 8 made on Wednesday December 22, 2004 at 22:02 |
vwpower44 Super Member |
Joined: Posts: | August 2004 3,662 |
|
|
not that it is correting the problem, but us an IR Repeater system on one and the RF on the other. Switch the one remote to RF and One to IR. Depending on if you can get an IR receiver in line of sight. Remeber to set the IR Receiver code in the MX software. That might be the problem. Program, Receivers, ID Code.
Mike
|
Stay Hungry, Stay Foolish... |
|
Post 9 made on Thursday December 23, 2004 at 16:57 |
Evil Twins Long Time Member |
Joined: Posts: | November 2003 132 |
|
|
Try using the the ir routing this should fix your issue. Put one room on port 1 and the other on say port 6 on the other repeater.
|
|
Post 10 made on Thursday December 23, 2004 at 20:14 |
Impaqt RC Moderator |
Joined: Posts: | October 2002 6,233 |
|
|
Are you sure one of em isnt set to 0? Zero picks up all... Had that today... Instalers didnt read the part of the report that said "Set ID to 1 on RF Receiver"... COuldnt figure out why none of my IR routing was working..... Then I noticedit was on "0" still... Grrrrr......
|
|
|
Post 11 made on Thursday December 23, 2004 at 20:54 |
jayson Long Time Member |
Joined: Posts: | July 2004 407 |
|
|
I tried one MX3000 and will never use them again. We swapped base stations and remotes, and tried every possible code and still could not get it to output on just the specified port.
|
|
Post 12 made on Thursday December 23, 2004 at 21:25 |
geraldb Long Time Member |
Joined: Posts: | June 2002 412 |
|
|
Try changing channels again on one of the 250's. Also, on that same 250, change the outputas well.
I just recently had output 1&2 sending signal to both devices at the same time, changed one of them to 6 and it worked fine
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|