|
|
 |
|
The following page was printed from RemoteCentral.com:
| Topic: | Just Add Power: no video This thread has 29 replies. Displaying posts 1 through 15. |
|
| Post 1 made on Friday July 20, 2018 at 12:35 |
Fins Elite Member |
Joined:
Posts: | June 2007
11,627 |
|
|
Client just sent me a pic of their master bedroom tv. It has a JAP Ultra HD logo in the middle of the screen and at bottom left “waiting for source” and bottom right has IP address. So how do I fix this?
|
Civil War reenactment is LARPing for people with no imagination.
|
|
| Post 2 made on Friday July 20, 2018 at 12:51 |
PostyMcPostface Long Time Member |
Joined:
Posts: | February 2018
17 |
|
|
Means the transmitter is not getting any video. Either the source is off or HDMI was unplugged
|
|
| Post 3 made on Friday July 20, 2018 at 14:29 |
cgav Select Member |
Joined:
Posts: | September 2009
1,568 |
|
|
Or the switch port went bad. Had that on a luxul switch yesterday. Although I would check everything else first.
|
|
| Post 4 made on Sunday July 22, 2018 at 17:08 |
andrewinboulder Select Member |
Joined:
Posts: | August 2003
1,518 |
|
|
I have a job where thia has happened twice in a few months. Each time a reboot of the Luxul switch fixed it. Not sure what would cause this. It’s been the same TV bothe times.
|
|
| Post 5 made on Sunday July 22, 2018 at 17:16 |
Jimmy Bellagio Advanced Member |
Joined:
Posts: | January 2008
854 |
|
|
Cisco is the only way.
|
James S. Bellagio |
|
| Post 6 made on Monday July 23, 2018 at 09:03 |
Duct Tape Loyal Member |
Joined:
Posts: | November 2008
5,299 |
|
|
On July 22, 2018 at 17:16, Jimmy Bellagio said...
Cisco is the only way. I just had a Cisco SG300-52P switch fail in a J+P system last week.
|
|
|
| Post 7 made on Monday July 23, 2018 at 09:29 |
lippavisual Senior Member |
Joined:
Posts: | December 2007
1,463 |
|
|
I don't use Luxul and never will, but Cisco certainly has its issues as well. I deal with Cisco problems almost weekly from ports going bad to power supplies just stopping. This still happens on fully conditioned and battery back-up data centers.
|
|
|
| Post 8 made on Monday July 23, 2018 at 12:17 |
On July 23, 2018 at 09:29, lippavisual said...
I don't use Luxul and never will, but Cisco certainly has its issues as well. I deal with Cisco problems almost weekly from ports going bad to power supplies just stopping. This still happens on fully conditioned and battery back-up data centers. On July 23, 2018 at 09:03, Duct Tape said...
I just had a Cisco SG300-52P switch fail in a J+P system last week. Right! I'm sick and effin tired of both brand of switches letting go. Our last Luxul let go a day before last Christmas on a 7X10 project. Cute. That was out last Luxul product ever. Even if they were free, um, no.
|
how in the hell does ernie make money? |
|
| Post 9 made on Monday July 23, 2018 at 13:43 |
Nded Just Add Power |
Joined:
Posts: | September 2009
348 |
|
|
The new justOS B.1.0.0 firmware we are releasing this week will support installing Just Add Power on just about any 1GB rated switch you can find.
|
Ed Qualls - Just Add Power - Proud to advertise on and support Remote Central |
|
| Post 10 made on Monday July 23, 2018 at 16:09 |
radiorhea Super Member |
Joined:
Posts: | May 2002
3,264 |
|
|
On July 22, 2018 at 17:16, Jimmy Bellagio said...
Cisco is the only way. +1000
|
Drinking upstream from the herd since 1960 |
|
| Post 11 made on Monday July 23, 2018 at 19:03 |
andrewinboulder Select Member |
Joined:
Posts: | August 2003
1,518 |
|
|
On July 23, 2018 at 13:43, Nded said...
The new justOS B.1.0.0 firmware we are releasing this week will support installing Just Add Power on just about any 1GB rated switch you can find. Sweet!
|
|
| Post 12 made on Monday July 23, 2018 at 19:44 |
goldenzrule Loyal Member |
Joined:
Posts: | July 2007
8,474 |
|
|
On July 23, 2018 at 13:43, Nded said...
The new justOS B.1.0.0 firmware we are releasing this week will support installing Just Add Power on just about any 1GB rated switch you can find. Will Jad Config still only setup with a Cisco? The config tool really makes it very easy to setup.
|
|
| Post 13 made on Tuesday July 24, 2018 at 09:34 |
Duct Tape Loyal Member |
Joined:
Posts: | November 2008
5,299 |
|
|
On July 23, 2018 at 19:44, goldenzrule said...
Will Jad Config still only setup with a Cisco? The config tool really makes it very easy to setup. Luxul too. And a few others I believe that aren't really suggested, but are in the JADConfig as options.
|
|
|
| Post 14 made on Tuesday July 24, 2018 at 09:37 |
goldenzrule Loyal Member |
Joined:
Posts: | July 2007
8,474 |
|
|
On July 24, 2018 at 09:34, Duct Tape said...
Luxul too. And a few others I believe that aren't really suggested, but are in the JADConfig as options. Oh yeah? I didn't realize. I have only manages Jap systems for a while now, haven't added any new ones so haven't used Jad Config in quite a while. Good to hear they added more than just Cisco which was all that was available when I last used it.
|
|
| Post 15 made on Tuesday July 24, 2018 at 17:31 |
On July 23, 2018 at 13:43, Nded said...
The new justOS B.1.0.0 firmware we are releasing this week will support installing Just Add Power on just about any 1GB rated switch you can find. Wouldn't this just add to the problems? Is there something out there better than the SG series for this specific purpose? Seems to me this would be an advantage of snap's new system -- thier own in-house brand -- one could get support with 3 years down the line if the switch fails.
|
how in the hell does ernie make money? |
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
