 |
 |
|
|
Custom Installers' Lounge Forum - View Post
|
|
 |
|
|
|
 |
|
The following page was printed from RemoteCentral.com:
|
Savant IR Hex Code in text form
| |
|
| Topic: | Savant IR Hex Code in text form This thread has 7 replies. Displaying all posts. |
|
| Post 1 made on Wednesday October 4, 2017 at 20:33 |
Hello all. I am trying to gain control of a tv lift that is not very accessible. The emitter is already in place and I am able to tie onto the cat 5 with an emitter head to verify I am sending codes to the general location. What I was given from previous installer was his "learned " codes for raise, lower and stop. I took the hex given to me and tried to put it into the RTI infrared library but I keep getting error unknown code type. Ive tried to break it up into sections of 4 but then I get invalid zero-length time detected. These supposedly came from a savant system. Anyone have any suggestions ?
000000000000A02800B8001A00B8001A00B8001A00B8001A00B8001A001B00B900B8001A001B00B900B8001A001B00B9001B00B9001B00B9001B00B9001B00B9001B00B9001B00B900B8001A001A033A00000000
up
000000000000A02800B8001A00B8001A00B8001A00B8001A00B8001A001B00B900B8001A001B00B900B8001A001B00B9001B00B9001B00B9001B00B9001B00B9001B00B9001B00B900B8001A001A033A00000000
down
0000000000009753000F0019000F003D000F0019000F003D000F0019000F003D000F0019000F0019000F003D000F0019000F0C01000F0019000F003D000F0019000F003D000F0019000F003D000F0019000F0019000F003D000F0019000F0C0100000000
stop
|
|
| Post 2 made on Wednesday October 4, 2017 at 22:28 |
Glackowitz RC Moderator |
Joined:
Posts: | May 2002
3,793 |
|
|
Do you have any bro on the lift? Manufacturer, model?
|
There's no worse feeling than that millisecond you're sure you are going to die after leaning your chair back a little too far. |
|
| OP | Post 3 made on Wednesday October 4, 2017 at 22:36 |
Unfortunately, I have none. t's all buried in a masonry fireplace too. Literally I have a cat 5 going into the back side through some cabinetry and thats it. It has a box attached to the top of the lift and then the tv is mounnted to the box There is a soundbar speaker that sits on the bottom of the box as well just below the tv. I dont want to disassemble the whole thing just to find a mfg, but it may be in the cards. I was just looking through the rti master library for lifts and checking to see if any of the code is similar to what the previous installers sent me
|
|
| Post 4 made on Thursday October 5, 2017 at 08:20 |
Duct Tape Loyal Member |
Joined:
Posts: | November 2008
5,297 |
|
|
can you take a photo of the spot that the emitter head is connected to? maybe someone can identify the system based on that.
|
|
|
| Post 5 made on Thursday October 5, 2017 at 08:50 |
ckwa Long Time Member |
Joined:
Posts: | February 2017
52 |
|
|
Perhaps look online for the various picture lift manufactures : Future automation and others. Find all of there IR codes and test them against your setup.
Theres not too many picture lift manufactures as far as i know.
|
|
| OP | Post 6 made on Thursday October 5, 2017 at 09:48 |
Thanks for reply Duct Tape there is no seeing anything of the lift or where the emitter is stuck unless I take it all apart from the masonry on the front. I'm truly flying blind that it is attached to a receiver inside the fireplace but at least everything else I've seen of some previous work is good glue on existing emitters on other sources.
CKWA thank you I've been researching tv lift and your suggestion will aid me in my search
|
|
| Post 7 made on Thursday October 5, 2017 at 10:06 |
Glackowitz RC Moderator |
Joined:
Posts: | May 2002
3,793 |
|
|
I tried playing with codes you posted and no luck. Couldn’t decipher them.
|
There's no worse feeling than that millisecond you're sure you are going to die after leaning your chair back a little too far. |
|
| Post 8 made on Thursday October 5, 2017 at 12:53 |
Impaqt RC Moderator |
Joined:
Posts: | October 2002
6,230 |
|
|
that looks like Savant format. Problem is the Savant IR Translator will go from Pronto to Savant.. But There doesnt seem to be any Savant back to Pronto button.
|
|
|
 |
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|
|
