|
|
|
Custom Installers' Lounge Forum - View Post
|
|
|
|
|
|
|
The following page was printed from RemoteCentral.com:
Topic: | House audio with 16/2 ?? This thread has 11 replies. Displaying all posts. |
|
Post 1 made on Thursday October 14, 2004 at 15:09 |
ericstac Long Time Member |
Joined: Posts: | October 2002 312 |
|
|
Okay I have a house that is wired with 16/2 to two of the three VC locations and then 16/2 going to the speakers. The other VC got 16/4. No Cat5 to any of the VC locations.
What can I do ..
I was thinking of mono-ing the signal then run the 16/2 to a VC and the series the two speakers..
|
|
Post 2 made on Thursday October 14, 2004 at 15:48 |
avdude Founding Member |
Joined: Posts: | February 2002 814 |
|
|
eric,
is the 16/2 by any chance shielded?
|
AVDUDE "It might work better if it were plugged in and programmed first...just a thought!" |
|
OP | Post 3 made on Thursday October 14, 2004 at 16:51 |
ericstac Long Time Member |
Joined: Posts: | October 2002 312 |
|
|
no luck there.. just basic 16/2.. it is like the prewire tech didn't know the difference between his wires or something and just ran wire to each location.. sucks because I have to figure it out..
|
|
Post 4 made on Thursday October 14, 2004 at 17:06 |
juliejacobson CE Pro Magazine |
Joined: Posts: | April 2003 3,032 |
|
|
|
Post 5 made on Thursday October 14, 2004 at 17:08 |
oex Super Member |
Joined: Posts: | April 2004 4,177 |
|
|
by a good amp that is very stable around 3 ohms. feed it mono , or convert signal to mono, put 16/2 on left input of VC with a jumper to the right input. Speakers go as normal. B&K or AudioControl amps should do it. Sonance Sonamps will too. Aint goingto be cheap!
|
Diplomacy is the art of saying hire a pro without actually saying hire a pro |
|
OP | Post 6 made on Thursday October 14, 2004 at 17:36 |
ericstac Long Time Member |
Joined: Posts: | October 2002 312 |
|
|
I was going to go with Onkyo TX-8511 for the three rooms.. very basic.
I was just going to set the receiver to mono and shoot the signal to the VC..
If I jump from Left to Right it will kick the ohms to 4 which is pushing it.. if I series them then it would push it to 16 ohms which will work just fine.. or am I wrong on this.
|
|
Post 7 made on Thursday October 14, 2004 at 21:56 |
oex Super Member |
Joined: Posts: | April 2004 4,177 |
|
|
3 pairs of 8 ohm speakers with VC's, if you jump channels together will result in a load SIGNIFICANTLY lower than 4 ohms. 4 ohms if you have 1 vc fed with 4 conductor and speaker per channel - you said you have 1. 2 ohm load with the 16/2 going to 1 vc. parallel these and your load is about 1.5 DISASTER FOR ANY RECIEVER. i would recommend putting the 16/4 on the reciever and getting an Audiocontrol 2 channel amp - stable at 2 ohm for the other 2 wires. Put one 16/2 per channel. Run the amp in mono. Others brands may be too but expect to pay around $ 600 for this screw up
|
Diplomacy is the art of saying hire a pro without actually saying hire a pro |
|
OP | Post 8 made on Friday October 15, 2004 at 08:28 |
ericstac Long Time Member |
Joined: Posts: | October 2002 312 |
|
|
The VC were going to be impedence matching as well as a speaker selector box..
|
|
OP | Post 9 made on Friday October 15, 2004 at 08:28 |
ericstac Long Time Member |
Joined: Posts: | October 2002 312 |
|
|
The VC's were going to be impedence matching as well as a speaker selector box..
|
|
Post 10 made on Friday October 15, 2004 at 08:46 |
Larry Fine Loyal Member |
Joined: Posts: | August 2001 5,002 |
|
|
Eric, you've got to work on those hiccups!
|
|
|
Post 11 made on Friday October 15, 2004 at 14:08 |
vwpower44 Super Member |
Joined: Posts: | August 2004 3,662 |
|
|
Matrix Audio (speaker wire technology) comes close, but don't think it can handle this job. Control and audio signals over single speaker wire. http://www.matrixaudiodesigns.comI think the matrix audio will work with only two wires. call their tech support. Might be too expensive for this job. Mike
|
Stay Hungry, Stay Foolish... |
|
Post 12 made on Friday October 15, 2004 at 23:40 |
Vincent Delpino Select Member |
Joined: Posts: | September 2004 1,818 |
|
|
there is nothing wrong with a summed stereo signal to a good speaker. stereo is often overused when there is no true listening area. many amps will let you sum l+r to a single chanel. its realy not a big deal to not have 2 speakers in a casual listening area.
|
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|
|
|