|
|
|
The following page was printed from RemoteCentral.com:
ONSITE: unifi outdoor ap+
| |
|
Topic: | ONSITE: unifi outdoor ap+ This thread has 23 replies. Displaying posts 1 through 15. |
|
Post 1 made on Wednesday July 23, 2014 at 11:50 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
connected but no traffic. No up, no down.... Not showing up on wifi analyzer either...
Last edited by Zohan on July 23, 2014 11:58.
|
|
Post 2 made on Wednesday July 23, 2014 at 11:58 |
SWOInstaller Select Member |
Joined: Posts: | October 2010 1,594 |
|
|
check your terminations of the RJ45's. I had this the other day where I could connect to the AP but couldn't get an IP address when I connected the AP to the router. problem ended up being a bad termination at the AP, re-terminated and worked no problem
|
You can't fix stupid |
|
OP | Post 3 made on Wednesday July 23, 2014 at 12:05 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
I thought about that because I had to use a keystone coupler, but the AP has an ip address and shows up on the network but not showing a wifi signal as per wifi analyzer app and therefore no traffic up or down...
|
|
Post 4 made on Wednesday July 23, 2014 at 12:25 |
Hertz Active Member |
Joined: Posts: | December 2007 657 |
|
|
Is the frequency set to 20 or 40? AirMax on by mistake?
|
|
Post 5 made on Wednesday July 23, 2014 at 12:34 |
jimstolz76 Loyal Member |
Joined: Posts: | December 2007 5,607 |
|
|
Yeah check that Airmax is UNchecked
|
|
|
OP | Post 6 made on Wednesday July 23, 2014 at 12:37 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
On July 23, 2014 at 12:34, jimstolz76 said...
Yeah check that Airmax is UNchecked Airmax? Ive only seen that on the regular waps, not on unifi....
|
|
Post 7 made on Wednesday July 23, 2014 at 12:57 |
Impaqt RC Moderator |
Joined: Posts: | October 2002 6,230 |
|
|
On July 23, 2014 at 12:37, Zohan said...
Airmax? Ive only seen that on the regular waps, not on unifi.... no airmax on unifi.... What version are you one Controller and AP's
|
|
|
OP | Post 8 made on Wednesday July 23, 2014 at 13:06 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
ap = Version 3.2.1.2601 controller = 3.2.1 just disconnected that ap and tried a different one also outdoor + and smae result. Then brought in here at rack where i am and connected with a short cable to the poe injector. I get same result, it connects and gets an ip address on the network, but no wifi signal showing up from it anywhere. The light on front is blue. All looks like it should, I can ping the ap, except no signal arrgghh
Last edited by Zohan on July 23, 2014 13:17.
|
|
Post 9 made on Wednesday July 23, 2014 at 13:33 |
lippavisual Senior Member |
Joined: Posts: | December 2007 1,463 |
|
|
I hope I don't have this issue tomorrow as I'm installing the same units for a client.
|
|
|
Post 10 made on Wednesday July 23, 2014 at 13:53 |
goldenzrule Loyal Member |
Joined: Posts: | July 2007 8,474 |
|
|
|
OP | Post 11 made on Wednesday July 23, 2014 at 14:02 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
On July 23, 2014 at 13:53, goldenzrule said...
Your device 5 GHz only? Not sure what you mean, but i have the outdoor + which is 2.4....it doesnt show up in either my wifi analyzer app on android (checked both 2.4 and 5) nor my laptop.....there is no signal emanating from the wap. Real frustrating.....ive changed cables, poe injectors, electrical outlets....
|
|
Post 12 made on Wednesday July 23, 2014 at 14:12 |
goldenzrule Loyal Member |
Joined: Posts: | July 2007 8,474 |
|
|
Don't know if the wifi analyzer would work if your devices were 5 GHz only. I'd be surprised if they are though. Is your AP assigned to your WLAN Group?
|
|
OP | Post 13 made on Wednesday July 23, 2014 at 14:14 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
On July 23, 2014 at 14:12, goldenzrule said...
Don't know if the wifi analyzer would work if your devices were 5 GHz only. I'd be surprised if they are though. Is your AP assigned to your WLAN Group? its assigned to the default group, there are no other wlan groups...thats how ive always done it. im trying a unifi ap indoor right now, its connected and upgrading...i will see if there is a signal from that one in a minute
|
|
OP | Post 14 made on Wednesday July 23, 2014 at 14:23 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
On July 23, 2014 at 14:12, goldenzrule said...
Don't know if the wifi analyzer would work if your devices were 5 GHz only. I'd be surprised if they are though. Is your AP assigned to your WLAN Group? Sh!#.....I think that was it! Ill post back in a few
|
|
OP | Post 15 made on Wednesday July 23, 2014 at 14:54 |
Zohan Super Member |
Joined: Posts: | September 2010 3,096 |
|
|
That was it. I don't know why but I dont recall ever setting up the wlan group name just left as default. Either i'm going nuts or maybe the firmware upgrade made that a necessity.
Either way it's working now.....
Thank you Mike
|
|
|
Before you can reply to a message... |
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now. |
Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.
|
|