Your Universal Remote Control Center
RemoteCentral.com
Complete Control by URC Forum - View Post
Previous section Next section Up level
Up level
The following page was printed from RemoteCentral.com:

Login:
Pass:
 
 

Topic:
IR Codes for Dish Hopper - MX-850
This thread has 11 replies. Displaying all posts.
Post 1 made on Monday September 3, 2012 at 09:16
HotRod19579
Long Time Member
Joined:
Posts:
March 2003
16
I recently upgraded by Dish 722 receiver to the Hopper. All of the 722 IR codes for my MX-850 work however I am missing the codes for the red, green, blue and yellow buttons. The remote that came with the Hopper is an RF remote therefore I cannot learn the codes.
Can anyone tell me how I can get these codes? I found one post that had the hex codes for the buttons and using the MX-850 editor I tried to use them but they didn't work.
Post 2 made on Monday September 3, 2012 at 10:10
KVH
Advanced Member
Joined:
Posts:
December 2006
911
Try these...

Red
0000 0048 0001 0011 0017 0162 0017 00A3 0017 0060 0017 00A3 0017 00A3 0017 0060 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Green
0000 0048 0001 0011 0017 0162 0017 0060 0017 0060 0017 00A3 0017 0060 0017 00A3 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Yellow
0000 0048 0001 0011 0017 0162 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Blue
0000 0048 0001 0011 0017 0162 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 0060 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162
All high's, all low's, it must be.......
Einstein @ URC Control Room forum
www.einsteinaudiosystems.com
OP | Post 3 made on Monday September 3, 2012 at 10:14
HotRod19579
Long Time Member
Joined:
Posts:
March 2003
16
These are the codes that I found and tried. After downloading them into the remote they didn't work.
Post 4 made on Monday September 3, 2012 at 13:31
TwistedMelon
Long Time Member
Joined:
Posts:
December 2004
435
According to this thread: [Link: dbstalk.com] (which references back to Remote Central) the codes are the same as previous Dish receivers. They're also pasted into that thread as OBC, which match precisely the codes above posted by KVH.

Protocol: Dish, Device: 0
OBC:
Red 19
Green 53
Yellow 34
Blue 35
https://TwistedMelon.com - Mira & Manta IR - Remote Control Your Apps
Post 5 made on Monday September 3, 2012 at 22:15
boogerboy
Long Time Member
Joined:
Posts:
January 2009
12
I have RTI control and made same upgrade. I made no changes to code base and it works fine. Clearly life isn't so easy on your end. If you can't dig up working codes here you can learn them from dish remote. Grab Dish remote select menu>settings>remotes manager>IR (bottom right corner) select enable and then save. These are two way remotes and it will change remote to send out IR and RF. Voila' learn codes straight to remote.
Post 6 made on Tuesday March 5, 2013 at 14:43
danmcg
Founding Member
Joined:
Posts:
March 2002
14
Pretty sure these are right. I found many more for these 3 functions, but these are the first that I came across for each one. Someone want to verify that they work on their Hopper also?

Live TV - 97
0000 0048 0001 0011 0018 0162 0018 005E 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 005E 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 0162

Search - 102
0000 0048 0001 0011 0018 0162 0018 005E 0018 00A5 0018 00A5 0018 005E 0018 005E 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 0162

On Demand - 116
0000 0048 0001 0011 0018 0162 0018 005E 0018 005E 0018 00A5 0018 005E 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 0162
Post 7 made on Tuesday March 5, 2013 at 16:14
edmund
Elite Member
Joined:
Posts:
April 2002
13,838
If they don't work for you, you probably have it set an address other than #1, which those are.
Post 8 made on Friday October 2, 2015 at 21:29
audvid
Founding Member
Joined:
Posts:
August 2001
114
On September 3, 2012 at 10:10, KVH said...
Try these...

Red
0000 0048 0001 0011 0017 0162 0017 00A3 0017 0060 0017 00A3 0017 00A3 0017 0060 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Green
0000 0048 0001 0011 0017 0162 0017 0060 0017 0060 0017 00A3 0017 0060 0017 00A3 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Yellow
0000 0048 0001 0011 0017 0162 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Blue
0000 0048 0001 0011 0017 0162 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 0060 0017 0060 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 00A3 0017 0162

Thanks KVH..
The codes you posted.. work just fine!
Post 9 made on Friday October 2, 2015 at 21:32
audvid
Founding Member
Joined:
Posts:
August 2001
114
On March 5, 2013 at 14:43, danmcg said...
Pretty sure these are right. I found many more for these 3 functions, but these are the first that I came across for each one. Someone want to verify that they work on their Hopper also?

Search - 102
0000 0048 0001 0011 0018 0162 0018 005E 0018 00A5 0018 00A5 0018 005E 0018 005E 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 00A5 0018 0162

I have tried the search code and it works just fine!
Thanks danmcg! This helped me a lot!
Post 10 made on Friday October 2, 2015 at 21:36
audvid
Founding Member
Joined:
Posts:
August 2001
114
By the way, if you are working how to enter hex codes into your ccp..
I use ccp with mx850.

In the tools, select universal browser.
It will open a new window.
Then you will see a little button in this browser window with hex written on it.
click on the hex. it will open a new window.
In this new hex window, you can paste the hex code you want.
select the button - say the green button - you want to program.. this will give you a window for this button.
Then click on the drag button in this window and drag that to the window for the green button

It is actually fairly simple..
Post 11 made on Saturday October 3, 2015 at 08:29
goldenzrule
Loyal Member
Joined:
Posts:
July 2007
8,470
On October 2, 2015 at 21:36, audvid said...
I use ccp with mx850.

you sure about that?
Post 12 made on Sunday August 28, 2016 at 10:47
cgperry
Lurking Member
Joined:
Posts:
August 2016
1
These codes also all work correctly in Crestron's Device Learner in Toolbox if anyone else was wondering.


Jump to


Protected Feature Before you can reply to a message...
You must first register for a Remote Central user account - it's fast and free! Or, if you already have an account, please login now.

Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. Other private buy & sell messages should be posted to our Marketplace. For information on how to advertise your service or product click here. Remote Central reserves the right to remove or modify any post that is deemed inappropriate.

Hosting Services by ipHouse